TorkLift Super Hitch and SuperTruss for 2008 GMC 3500 and Camper Tie-Downs

Question

Question:

just got torklift super hitch 20k how i would like to get camper tie downs for front and back on my 2008 3500 ext cab ....also some turnbuckles can you send me part numbers thanks

asked by: Jeff H

1

Helpful Expert Reply:

The TorkLift SuperTruss Hitch Extension for SuperHitch Trailer Hitch Receivers - 24" Long # TLE1524 utilizes the 2 inch double receiver. For your 2008 GMC Sierra 3500 you will use # TLC1205.

expert reply by: Jason S

1

Jeff

5/13/2020

just got torklift super hitch 20k how i would like to get camper tie downs for front and back on my 2008 3500 ext cab ....also some turnbuckles can you send me part numbers thanks

Jason S.

5/13/2020

The TorkLift Tie-Downs Needed depend on bed length and whether you have running boards or steps underneath your rocker panels. If you have the 6-1/2 foot Bed: -with board or step underneath use # TLC4203 and # TLR3500 -without board or step underneath use # TLC2205 and # TLR3500 If you have the 8 foot bed: -with board or step underneath use # TLC4203 and # TLR3503 -without board or step underneath use # TLC2204 and # TLR3503 You may also be interested in the TorkLift Locking FastGun Turnbuckles for Frame-Mounted Tie-Downs - Stainless Steel - Black - Qty 4 # TLS9529-2-LK or two sets of the TorkLift Basic SpringLoad Turnbuckles for Camper Tie-Downs - Qty 2 # TLS9000.

Answer 1

Hi Brandon; what kind of camper do you have? Assuming your Tundra is 4WD with no running boards, or cab length running boards, you can use the TorkLift Tie Downs - Custom Frame Mount - Front and Rear #TL85VV. You will also need turnbuckles like the…

view full answer...

Answer 2

Hello Mike, Sounds like you are getting things set up the right way and not going over your payload, I respect that. It looks like the weights are the same whether you have a 6 3/4' or 8' bed. If you happen to have an aftermarket hitch,…

view full answer...

Answer 3

For your 2004 GMC Sierra 2500HD we have the Draw Tite part #41944 which is a Class V confirmed as a fit for your truck once you remove the factory hitch. This will also work with your front Torklift tie down #TLC2205 but you'll need to go with a…

view full answer...

Answer 4

Hi Jonathan, Actually, nothing will make the Curt Trailer Hitch Receiver #C15703 not fit your 2002 Chevy Silverado 2500HD if you remove the factory hitch. If you remove that hitch, you can absolutely install the #C15703.

view full answer...

Answer 5

Curt Trailer Hitch Receiver #C15703 hangs pretty low on a 2005 Chevy Silverado 2500. From the bottom of the bumper to the top of the hitch receiver it is approximately 4 inches. I have included a picture showing the gap. A similar hitch, #C15302,…

view full answer...

Answer 6

The only other part that comes in the package of your TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear #TLR3501 apart from the parts you mentioned is the metal pin/clip that attaches the tie-down shank into the receiver shank. I went ahead and…

view full answer...

Answer 7

I had our warehouse measure the Curt Trailer Hitch Receiver #C15703 you were looking at, and has an overall width of 40-5/8", overall length of 29". The distance between the vertical mounting holes is 14-1/2" center to center, and the…

view full answer...

Answer 8

Ground clearance is generally not a problem on full size trucks like your 2007 Chevy Silverado 3500. With that said the 2-1/2 inch hitches for the truck do hang fairly low. The Draw-Tite hitches #DT45519 and #DT45517 fit a little tighter to the rear…

view full answer...

Answer 9

If the tube step on your 2006 Chevy Silverado 2500 short bed is only under the cab of the truck and no part of it is attached beyond the back of the cab then you would look at the tie downs for models without a board or step under the truck bed and…

view full answer...

Answer 10

It sounds like you are looking for a rear set of camper tie downs for your 2008 Chevy Silverado 3500 dually with the Curt hitch part #C15703. For that we have the Torklift set part #TLR3501 which I confirmed with Torklift as a fit.

view full answer...

Answer 11

The #TLC3205 you have now is only designed to work with the factory hitch. Whether it is the #DT45517, a Curt hitch, or even a TorkLift hitch you will need a different rear tie-down. The correct rear tie-down for a 2002 Silverado 2500 without a board…

view full answer...

Answer 12

I'm not 100 percent certain about the exact measurement you are looking for; is it the vertical measurement of the bolt hole on the frame brackets to the hitch tube itself or the horizontal measurement from the bolt hole to the rear of the hitch…

view full answer...

TorkLift Super Hitch and SuperTruss for 2008 GMC 3500 and Camper Tie-Downs

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching