Stake Pocket Holders and J-bolts for Ladder Rack

Question

Question:

Hello, I’m looking for ladder rack hardware. J bolts steel. Or will aluminum work? Ladder rack uses stake pocket t bolts and 4 j bolts. Do you have these? Thanks

asked by: David R

1

Helpful Expert Reply:

We have the Replacement Stake Pocket Insert for Adarac Custom Truck Bed Ladder Rack - Aluminum - Qty 1 # A70432 for your stake pockets and the UWS Replacement J-Bolts for Crossover Toolboxes - Qty 2 # UWSJBOLT.

I don't know if that will work for your rack, but it sounds like what you are seeking.

expert reply by: Jason S

1

Answer 1

Yes, the capture plate on the Stake Pocket Insert part #A70432 allows it to work on practically any stake pocket opening including the ones on your 2014 Ford F-150. It sounds like you may have an alternate application for these but nonetheless I have…

view full answer...

Answer 2

I have a solution for you, but Adarac specifically states that their ladder racks are not compatible with other bed-rail-mounted or stake-pocket-mounted accessories such as tool boxes. So the Adarac Custom Truck Bed Ladder Rack - Steel with Aluminum…

view full answer...

Answer 3

The Adarac Custom Truck Bed Ladder Rack #A70450 has a 500 lb rating, that would mean the stake pocket mounts would have at least the same rating. For replacement mount for this ladder rack you would want the part #A70432 which is a replacement stake…

view full answer...

Answer 4

Yes, the Replacement Rear Stake Pocket Insert for Adarac Custom Truck Bed Ladder Rack #A90165 and the Replacement Stake Pocket Insert for Adarac Custom Truck Bed Ladder Rack #A70432 are different from each other. The main difference is that the…

view full answer...

Answer 5

Hey Mike, if you are referring to the Replacement Stake Pocket Insert part #A70432 this actually fits the front and back stake pockets. It is not front exclusive.

view full answer...

Answer 6

I had our warehouse measure the lower threaded bracket included with the Replacement Stake Pocket Insert for Adarac Custom Truck Bed Ladder Rack #A70432 and it measures 2-7/8" long x 2" wide and 3/16" thick as shown in the included…

view full answer...

Answer 7

Yes, because the Adarac Ladder Rack part #A70530 is a confirmed fit for your 2009 Chevy Silverado 6-1/2 foot bed the replacement stake pocket part #A70432 would fit the vehicle.

view full answer...

Answer 8

Thule has a separate mounting bracket kit #TH41000 to mount a toolbox to the Thule TracRac TracONE Truck Bed Ladder Rack #TH27000XTB. This would clamp to the bedrails/base of the rack and provide you with an attachment point for your toolbox to bolt…

view full answer...

Answer 9

For your 2018 Ford F-150 the TracOne ladder rack will use the Toolbox Mount Kit for Thule TracRac TracONE Truck Bed Ladder Racks #TH41000 to give you the compatibility you are seeking by providing threaded holes for your toolbox instead of using J…

view full answer...

Answer 10

Yes, I have attached a full installation video below on the Adarac Custom Truck Bed Ladder Rack like #A90230, in which the installer shows how the Stake Pocket Brackets #A70432 are assembled and mounted. I have attached the written manual as well…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Stake Pocket Holders and J-bolts for Ladder Rack

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching