Replacement Power Cord for Thomas Payne Theater Seating

Question

Question:

I am looking for a replacement wiring kit for my Thomas Payne theatre chairs in my camper. It has heat lights and massage.

asked by: Nathan T

0

Expert Reply:

It sounds like you've got a Thomas Payne Seismic Dual Power Reclining RV Loveseat w Console, Heat, Massage, LEDs like the # 195-091-092-090, and you need the power plug for it. In this case you'll want to use the Replacement Power Cord with Power Supply Box for Thomas Payne Seismic RV Power Reclining Sofas # 195-000111 which is a confirmed fit for your theater style seating.

expert reply by: Erik B

0

Answer 1

According to Air Lift, there are a few things that can cause this issue. The problem is likely an air leak between the manifold and the compressor or simply a weak compressor that would need to be replaced. To get the compressor running again so you…

view full answer...

Answer 2

To replace the electrical cords for the Thomas Payne Seismic Dual Power Reclining RV Loveseat w/ Heat, Massage and LEDs, you will want to use the Replacement Power Cord #195-000111.

view full answer...

Answer 3

Behind the Thomas Payne Seismic Recliners there are power connections on either end. These are located near the edges of the recliners near the bottom (see attached photo "C" connections). You'll simply push the Replacement Power Cord…

view full answer...

Answer 4

You will only need one Replacement Power Cord with Power Supply Box for Thomas Payne Seismic RV Power Reclining Sofas #195-000111 for your sofa as both sides are connected electrically during assembly.

view full answer...

Answer 5

The Replacement Power Control Box for Thomas Payne Seismic Recliners and Sofas #LC36FR is the correct part for your Thomas Payne Seismic Series Recliner. If you have not already, preform a hard reset on your chair before continuing. To do this unplug…

view full answer...

Answer 6

I took a look at how you can power your Thomas Payne Seismic Recliners, using the: -Replacement Power Cord with Power Supply Box for Thomas Payne Seismic RV Power Reclining Sofas #195-000111, you will need to plug one end of the power cord into a…

view full answer...

Answer 7

I wasn't able to find anything with that part number, but if you have a Seismic series sofa, then you'd want the Replacement Power Cord with Power Supply Box for Thomas Payne Seismic RV Power Reclining Sofas #195-000111, but if you have a…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement Power Cord for Thomas Payne Theater Seating

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching