Will No Drill 7-Way Mount # 18140 Fit Curt Hitch of 2016 Lexus RX350 F-Sport

Question

Question:

Will this fit the curtis hitch #c13272 for my 2016 lexus Rx350 F Sport? If so, how do i install. thank you

asked by: MARCO M

0

Expert Reply:

Yes, the No-Drill mount # 18140 will fit the Curt # C13272 that you referenced. Basically you wrap the band clamp around the main hitch tube and then feed it into the opening of the clamp and then start screwing the head of clamp and it will start to tighten.

expert reply by: Jameson C

0

Answer 1

Hey Jerry, welcome back! The Curt Trailer Hitch #C54GJ is the best option and specifically designed for Wilderness models, great choice! Since you want to add a brake controller, you will also need the Curt #C56040 and the #ETBC7 for your wiring.…

view full answer...

Answer 2

Hey Jerit, congrats on the new car. We've got a couple of hitches that fit the 2026 Subaru Crosstrek Wilderness. The etrailer Trailer Hitch item #e98912 is going to be the most affordable option. This custom fit class III hitch has a 2"…

view full answer...

Answer 3

Hello Mike, thanks for reaching out. We do offer a few different hitches for the 2026 Subaru Crosstrek, the Curt #C22MJ, the Draw-Tite #76209 and the EcoHitch #EH57CR. All 3 of these hitches place the receiver in virtually the same position beneath…

view full answer...

Answer 4

Hey Chris. The Trailer Mate Trailer Hitch item #TMT94FR weighs 25 lbs. It has been confirmed to fit the 2025 Subaru Crosstrek. The bottom of the receiver sits 11-1/2" above the ground. It has a 1,500 lbs towing capacity and 150 lbs maximum…

view full answer...

Answer 5

Hey Brian, sorry for any confusion but we do have the Curt hitch 13634 you are looking for with the part #C54GJ which is a fit for your 2025 Subaru Crosstrek Wilderness.

view full answer...

Answer 6

You will need to use the spacers so that the Curt Hitch part #C13135 that you referenced will sit level when installed on your 2013 Subaru Crosstrek. As long as the carriage bolts are fully inserted through the square spacers used in the frame rails…

view full answer...

Answer 7

Hey Mike, The spacers are optional and just there to help level the etrailer Trailer Hitch Receiver #e98912. You can dry fit the hitch without them and place a level on the receiver tube to see if you're good or with need to use them. In the…

view full answer...

Answer 8

The spacers that come with the etrailer hitch that fits your 2022 Subaru Crosstrek are designed to be used as a way to level the hitch as needed. So if using them causes your hitch to not sit level I would recommend removing them.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Will No Drill 7-Way Mount # 18140 Fit Curt Hitch of 2016 Lexus RX350 F-Sport

Products Featured in This Question

Continue Researching