Metal Handle Replacement for Valterra Waste Valve on RV

Question

Question:

This just happened to my 2019 Fleetwood Discovery, black and gray tank valve handles. as you can see in the picture the plastic does not seem very sturdy. Is there an aluminum version of this kind of thing?

asked by: Carey

0

Expert Reply:

Valterra does offer a metal version of the handle you sent in a picture of with the part # T1003-6MNVP.

expert reply by: Jameson C

0

click to enlarge

Answer 1

If you're just needing the handle part of your waste valve then you should be able to use either the Replacement Handle for LaSalle Bristol Cable-Actuated RV Waste Valves #34490CMA1G which uses a screw to install, or the Replacement Handle for…

view full answer...

Answer 2

Hey Michael, thanks for reaching out. So, there isn't a square panel for the Redarc Tow Pro liberty controller, so if you want to use that on your 2025 Tacoma, you will have to do so without the panel. That said, what you can do is get the Redarc…

view full answer...

Answer 3

The easiest way to install a brake controller on your 2022 Toyota Highlander with a 4-way is to first install a 7-way kit with the part #TK57VR which includes brake controller wiring as well. Then for a brake controller the Curt Echo Mobile part…

view full answer...

Answer 4

The 2023 Toyota Highlander does not have a factory tow port or custom wiring harness for brake controller installation. However, if you're installing the Tekonsha 7-way #TK57VR you were looking at it comes with an adapter that will plug into…

view full answer...

Answer 5

Hello Dan, We can most definitely get you set up to use your Redarc Tow-Pro Liberty brake controller in your 2022 Toyota Highlander. Since you were looking at the #ETBC7, I’m assuming your Highlander does not have the factory tow package. To equip…

view full answer...

Answer 6

Yes, the Tekonsha OEM Replacement Vehicle Wiring Harness w Brake Controller Adapter #TK57VR is what you want to get a fully functioning 7-Way on your 2023 Toyota Highlander. I also recommend picking up the mounting brackets #PK12711U and #C57202 to…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Metal Handle Replacement for Valterra Waste Valve on RV

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching