Trailer Jack Replacement for Shelby 5862A

Question

Question:

Hi, I have a Shelby trailer jack, model 5862A. it is a bolt on swivel type rated for 1000 lbs. i’ m not 100 on the lift but i think it has a 10 inch lift. i’d like to purchase a Fulton model and am looking at the FTP10 and FTJ12000101 models. both of them rated for 1200 lbs. are these replacements for my Shelby jack

asked by: Doug C

0

Expert Reply:

To replace your Shelby 5856A jack I recommend the Fulton Round Snap-Ring Swivel Marine Jack # FTJ120W0301. We have had customers say that this fits the mounting plate for the Shelby 5784A perfectly so ti's going to be the easiest install possible. This jack features a lift capacity of 1,200 pounds, a lift total of 10 inches, and an outer tube diameter of 2 inches, and a snap ring pilot hole of 2-1/2 inches in diameter.

The # FTJ12000101 has the same dimension snap ring so it should work too.

expert reply by: Jameson C

0

Answer 1

Hey Dan. If your jack mount has a 2-1/2" ring on it then the Round Snap Ring Swivel Jack w/ Footplate item #TJB-2002S-B is going to be your best option. This 2,000 lbs capacity jack attaches to the same size bracket that the Fulton item…

view full answer...

Answer 2

I believe the jack you are looking for a replacement for is a frame mounted, swivel jack, sidewind, that has a 2,000 lb capacity and a wheel caster. We did have a customer come back and say that the Fulton jack part #FTJ120W0301 will attach just fine…

view full answer...

Answer 3

The Shelby 5730 I believe is a 1200 lb swivel jack with wheel. It is frame mounted. For a comparable replacement, I recommend the Fulton Round, Snap-Ring Swivel Marine Jack - Bolt On - Sidewind - 10" Lift - 1,200 lbs #FTJ12000101. This will fit…

view full answer...

Answer 4

I do have an option for you but Shelby boat trailer jacks are discontinued and we don't offer any direct bolt-on replacements for them. That said, you can easily remove the old flange by cutting or simply place the new jack beside it and leave…

view full answer...

Answer 5

It is possible the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will fit the same mount used by your Shelby 5776 jack but we do not have the exact dimensions of the mount used by your Shelby jack so you will need to take a quick…

view full answer...

Answer 6

The hole in the bracket of the Fulton 1200 lb Snap Ring Swivel Jack #FTJ12000101 is 2.55 inches in diameter to accommodate the 2-1/2 inch diameter flange on the trailer mounted bracket that the snap ring attaches to. The 2-1/2 inch diameter flange on…

view full answer...

Answer 7

Hey Dave, The snap ring on the Jack #FTJ12000101 you purchased isn't a bad thing. I would say it's the older style and it can sometimes be annoying to remove, but as far as functionally goes, it won't have a negative impact on how the…

view full answer...

Answer 8

I do have a solution for you, however replacement parts for your Shelby 5854A Trailer Jack are no longer available. I recommend simply replacing your Shelby jack with a similar unit like the Fulton Bolt-Thru Swivel Trailer Jack #FXPD15L. This zinc…

view full answer...

Answer 9

We have the Fulton trailer jack part #FTJ120W0301 which we know fits the same trailer mount as the Shelby 5856A that you have so this would be our best option for a solid jack with a very easy install. This jack has a 1,200 lb capacity, a wheel…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Trailer Jack Replacement for Shelby 5862A

Featured Help Information

Miscellaneous Media

Continue Researching