Instructions for Replacing Cover of Pace Edwards JackRabbit

Question

Question:

once I get the replacement cover, How do I get the old one out? is there a retractable spring that has to be rewound?

asked by: Jim

1

Helpful Expert Reply:

I spoke with Pace Edwards and they sent me an install instructions sheet for replacing the cover of a Pace Edwards JackRabbit Tonneau Cover. I attached the instructions to this page for you to check out. You do have to rewind the cover's spring but it's not like a garage door spring that is dangerous to wind.

expert reply by: Jameson C

1

click to enlarge

Answer 1

I spoke to my contact at Pace-Edwards he said that when installing a replacement cover, like the Replacement Cover for Pace Edwards JackRabbit Hard Tonneau Cover #311-TRPT1472-2007, the typical way he recommends to keep the tension on the spring is…

view full answer...

Answer 2

Nickis, it sounds like you're looking for the Replacement Reel/ Spring Assembly for Pace Edwards Tonneau Covers #PE86RB which is going to be the replacement reel/spring assembly and will work for the SwitchBlade, UltraGroove, and JackRabbit…

view full answer...

Answer 3

There isn't a wire schematic available to the public for the Pace Edwards Bedlocker Retractable Hard Tonneau Cover #311-M-BLFA18A44, but it's just a power and ground wire combination so there really isn't much to it. I recommend checking…

view full answer...

Answer 4

Typically if a Pace Edwards Retractable Tonneau Cover like the #311-M-BLFA18A44 is getting hung up it's with the railing and would require lubrication. The canister is a closed system so there isn't a good way to get into it and see if the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Instructions for Replacing Cover of Pace Edwards JackRabbit

Continue Researching