Right Lug Stud Size For 3,500 lb Lippert Axle

Question

Question:

I have a 2017 Carson 18’ car hauler with 3,500 lb axles. Is this the right lug stud?

asked by: Sean

0

Expert Reply:

In order to determine if the Trailer Hub Wheel Stud # 7-122 will work, you will need some measurements from your current studs.

Referring to the the included diagram, you will need to at least have the measurements for A, C, and E. You will want to use a dial or digital caliper because precise measurements are needed.

expert reply by: Patrick R

0

click to enlarge

Answer 1

The standard replacement drive-in wheel stud for a 3,500 lb hub/drum like what you have on your Lippert 3,500 axle is the part #7-122 which is the correct thread size and length.

view full answer...

Answer 2

Hey Howard, in general people don't balance trailer wheels and tires as it doesn't seem to make enough of a difference for it to be worth it but the tire of the Westlake ST205/75R15 Radial Tire w 15" Eagle Aluminum Wheel #WST69FR that…

view full answer...

Answer 3

Hey Brian, we do have black center caps you could get with the Provider ST205/75R15 Trailer Tire with Black Viking Aluminum Wheel #A15R45BML What trailer are these bad boys going on?

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Right Lug Stud Size For 3,500 lb Lippert Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching