Can Brake Parts be Replaced on Dexter 2,800 Pound Axles with Weld-On Trailer Brake Assemblies
Updated 06/13/2012 | Published 06/11/2012
Products Featured in This Question
Question:
I have a 1997 coachmen catilina lite travel trailer. the identification of these axles are Dexter 2800 lbs max cap. serial number 2102232 and 2102233. Model 2800 SLR 12.8. Dexter is telling me that I must replace the whole axle. Because the backing plate is welded to the axle. Isnt there a replacement shoe for this application? And new hardware. springs, adjuster etc..
asked by: James
Expert Reply:
What you were told was only partially correct. If you wanted to replace the entire brake assembly but you had welded on brakes then you could not replace the assemblies. However, you can replace the worn brake parts.
There should be a number on the hub if it is a Dexter hub, with an 8-XXX, the Xs being some 3 digit number Dexter uses. With this number we can determine a little about the axles and see what kind of brake parts you need.
Also, you can look at the brakes and if they are bolted on then that is a clear indication they are not the weld on type. If it is the weld on type, then the shoe you have referenced, # bp04-065 would be correct. The adjuster is # BP10-060. Arms and springs are available and I can have them added to our site if needed.
Product Page this Question was Asked From
10" x 1-1/2" Electric Brake Shoe/Lining (One Wheel)
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- LH
- RH
- Brake Shoes
- 10 x 1-1/2 Inch
- Dexter
more information >
Continue Researching
- Search Results: 67048
- Search Results: trailer bearings races seals caps
- Search Results: 10~19 grease seal
- Search Results: race l68110 trailer bearings races seals caps
- Search Results: race l68111 and l44610 trailer bearings races seals caps
- Search Results: grease seal 10 19
- Search Results: bearing l44649 trailer bearings races seals caps
- Shop: Replacement Magnet Kit for 10" Electric Trailer Brake Assemblies - 3,500 lbs
- Shop: 10" x 1-1/2" Electric Brake Shoe/Lining (One Wheel)
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Replacement Spring Kit for 10" and 12" Manual-Adjust Electric Trailer Brake Assemblies
- Shop: Timken L68111 Replacement Race for Bearings L68149, L68149A, and More - Qty 1
- Shop: Timken L44610 Replacement Race for Bearings L44643, L44649, and More - Qty 1
- Shop: Timken Replacement Bearing and Race Set # 6 - LM67048 and LM67010
- Q&A: Replacement Bearing And Seals For UFP Hub H-1062-2
- Q&A: Replacement Axles for Dexter 2800 lb Round Tube Straight Trailer Axles on 5th Wheel Trailer
- Shop: Trailer Hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Shop: Suspension Enhancement
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Drum - AKHD-545-35-EZ-K
- Shop: Gooseneck Hitch
on Accessories and Parts
