Replacement Bearing And Seals For UFP Hub H-1062-2

Question

Question:

Do you sell a Bearing/Seal kit for a UFP Hub H-1062-2? I have seal savers installed on the spindles. I also need dust covers for the same hubs - 1.9700 in. Thanks

asked by: Greg S

0

Expert Reply:

Hey Greg,

There unfortunately there isn't a guide to tell us the bearing and grease seal combination for your hub so you'll have to remove it and check the bearings/seal for their part numbers or use a digital caliper # PTW80157 to measure the spindle at points B, C, and D from the diagram below.

We unfortunately do not have a grease seal with a 1.9700" diameter.

expert reply by: Kevin C

0

Spindle Measurement Guide
(click to enlarge)

Greg

4/2/2024

Seal - 1.38 with seal saver installed Inner Bearing - 1.143 Outer Bearing - 1.065

Kevin C.

4/4/2024

@Greg Unfortunately it looks like we do not have the correct bearings for your spindle. At this point the only option we can offer would be replacement of the axle to get a more common spindle. If you can't find the correct replacement somewhere else and decide to bite the bullet on a new axle then give our customer service department a call at (800) 298-8924 and we can help walk you through the ordering process.

Greg

4/4/2024

@KevinC Thanks so much for your help. I was able to reuse my bearings and seal as they were in really good condition. The trailer does not get a lot of use. I will run it for a while and keep an eye on it. One day I will have to just get a new axle. Thanks again.

Answer 1

What you were told was only partially correct. If you wanted to replace the entire brake assembly but you had welded on brakes then you could not replace the assemblies. However, you can replace the worn brake parts. There should be a number on the…

view full answer...

Answer 2

Hey Tony, I would want all free-backing plates on a boat trailer if it was me as it allows you to back up the trailer easier. Basically they prevent the brakes from applying if you were ever to need to back up on a flat surface or a up a hill.…

view full answer...

Answer 3

You are correct that is a 3,500 lb axle. If you want a bearing kit the #BK2-100 you looked at is the right one. This comes with a #L44649 outer and #L68149 inner bearing along with a #58846 (10-19) grease seal. If you want a replacement idler hub you…

view full answer...

Answer 4

We will need some more information in order to track down a new hub to fit your assembly K-H 71744. Pull off your old hub and look for numbers stamped into the bearings. If you do not see the numbers then you will need to use 4" Carbon Fiber…

view full answer...

Answer 5

To check for a Free Backing Hydraulic Trailer Brake #AKFBBRK-35 you will need to remove your brake drum assembly. The free backing brakes have a different front brake shoe. This shoe is designed to fall away when the trailer is moving in reverse. The…

view full answer...

Answer 6

Hi Steve! For salt water applications, I always recommend Aluminum wheels. Galvanized steel will hold up better than raw or painted steel, but aluminum is king in this regard. You still want to clean them off after they get all salty as aluminum does…

view full answer...

Answer 7

We do have a solution for replacing your obsolete Dexter trailer axle but it isn't your standard trailer axle as none of ours matches that description. If you want to stick with a standard axle you need to contact a trusted trailer shop to have…

view full answer...

Answer 8

For a Lippert 4,400 lb trailer axle the correct bearing kit is the part #BK2-100 which includes inner bearing #L68149, inner race #L68111, outer bearing #L44649, outer race #L44610, grease seal #58846, a cotter pin and a tang washer.

view full answer...

Answer 9

To do what you're wanting to do, you'd need to contact the manufacturer of the trailer with the VIN. If you could provide me with the diameter of your rotors, their wheel bolt pattern, and the reference numbers from your inner and outer wheel…

view full answer...

Answer 10

The Kodiak Disc Brake Kit part #K2HR35DS is a great option to replace the disc brakes on a Shoreland'r Boat Trailer. It has dacormet and stainless steel finishes so it will hold up to salt water just fine. The hubs and rotor are integrated into…

view full answer...

Answer 11

For saltwater boat trailer use it is recommended to go with either a galvanized steel rim or a aluminum wheel. For a galvanized option I recommend the Americana Steel Spoke Trailer Wheel part #AM20354. Both these rims have excellent corrosion…

view full answer...

Answer 12

The DeeMaxx Trailer Idler Hub #DE36VR is designed to fit with DeeMaxx 10" Rotor with Maxx Coating #DE47VR or Stainless #DE67VR. Typically you will get either the Maxx Coating Brake Kit #DE42FR or Stainless Brake Kit #DE72FR which includes the…

view full answer...

Replacement Bearing And Seals For UFP Hub H-1062-2

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching