Can Follow Leg of Landing Gear be Replaced with Lead Leg with Different Specs Than Current Lead Leg
Published 01/28/2020
Products Featured in This Question
Question:
I have a 2018 Keystone Hideout 308BHDS. The current single motor landing gear just isn’t sufficient, and I plan on adding a second motor/lead leg. My question is the motor in the LG-5 kit. It calls for the LG-142178 which is a 5500rpm motor. The existing motor is a LG-196308 which has a higher weight rating an slightly slower RPM of 5430. Would that make a big difference?
asked by: Scott T
Expert Reply:
I believe you are referring to the # LG-2 kit as it is the one with the 5,500 lb Motor # LG-142178 with it. Ultimately as long as you aren't exceeding the weight capacity of your landing gear and you have individual switches for each leg you should be just fine. Yes the RPMs are different, but they aren't relying on each other so you just have to pay attention when each leg makes contact with the ground.
If you'd rather go with a matching set I recommend the Reese Electric 5th Wheel Landing Gear Set # RP500708 because it has an 8K weight capacity (which should be more than enough for your needs), weld stops that have the standard 15-1/2" inside and 17-1/2" outside measurements, quick-release pins to make dropping the legs quicker, and a control panel with a dual switch so you have a really clean look after everything is installed.
Product Page this Question was Asked From
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs
- Camper Jacks
- 5th Wheel Camper
- Landing Gear
- Steel
- 5001 - 6000 lbs
- Electric Jack
- 35 Inch Lift
- Weld-On
- 2 Jacks
- Stromberg Carlson
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: 142178
- Search Results: wheel chocks
- Shop: Lippert Electric Landing Gear Set - 37" Lift - 6,000 lbs
- Search Results: rp500708
- Search Results: lg 179014
- Shop: Replacement Motor for Stromberg Carlson Electric Landing Gear - 5,500 lbs
- Shop: Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for RVs
- Video: Ultimate Overview of the Lippert Electric Landing Gear Set
- Q&A: Recommended Replacement Landing Jack System for 2008 Keystone Montana Mountaineer 345DBQ
- Q&A: Replacement Heavy Duty Motor For Landing Gear On 2010 Keystone Raptor Toy Hauler
- Video: The Low-Down on the Replacement Motor for Stromberg Carlson Electric Landing Gear
- Shop: Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies
- Shop: Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin
- Shop: Fastway ONEstep Wheel Chock for Tandem-Axle Trailers and RVs - 16" to 24" Long
- Shop: Fastway ONEstep Wheel Chocks for Tandem-Axle Trailers and RVs - 16" to 24" Long - Qty 2
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer jack
- Shop: Trailer Wiring
- Article: Trailer Wiring Diagrams
- Video: Bigfoot Hydraulic Jack DIY Installation - Diamond C Trailer
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: etrailer 5K Electric A-Frame Trailer Jack with 7-Way Comprehensive Review
- Q&A: What Sealant Should I Use Between an Aluminum Jeep-Style Fender and My Trailer?
- Search Results: trailer tires and wheels
- Shop: Trailer Hitch
- Video: Hands-On with the Hub Saver Hub and Wheel Protector
- Shop: Suspension Enhancement
- Search Results: spare tire mount
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
on Camper Jacks
