How Does the Dutton-Lainson StrongArm Electric Winch Mount to a Trailer?

Question

Question:

How does this mount to a trailer?

asked by: Tom B

0

Expert Reply:

The Dutton-Lainson StrongArm Electric Winch w/ Remote # DL25019 has a die-formed base that allows for quick and easy mounting to a variety of surfaces. I've attached a photo to this answer that shows the holes in the base of this winch that you'll use when mounting.

To mount this winch you can use the Dutton-Lainson Quick Mount Kit # DL70309 or the Dutton-Lainson Mounting Adapter Plate for StrongArm Electric Winches # DL24055. You can also use 3/8" Grade 2 or Grade 5 screws into your trailer frame that can be sourced from your local hardware store.

expert reply by: Erik B

0

click to enlarge

Answer 1

The Dutton-Lainson StrongArm Electric Trailer Winch - Marine - 1,500 lbs #TW4015 requires a winch stand or mounting bracket. For the StrongArm you can use the Dutton-Lainson Mounting Adapter Plate for StrongArm Electric Winches #DL24055 if you have a…

view full answer...

Answer 2

The 520EM925AWWKIT trim kit included with the High Pointe Standard RV Microwave #HP39ZR is approximately 20.75” W x 15” H.

view full answer...

Answer 3

We do have the Dutton-Lainson StrongArm Electric Winch #DL24870 with a remote. Instead you'll want to use part #DL25010.

view full answer...

Answer 4

The Fulton F2 Fully Enclosed Trailer Winch #FW20000301 does not have any kind of adapter plate to allow you to mount it to a different bolt pattern. You will have to drill new holes if you want to use this winch. I attached a diagram below with the…

view full answer...

Answer 5

The Replacement Spring #4769-28 that you referenced will install onto the pawl assembly of your winch. Check out the pictures I attached that show an exploded diagram to see how it installs.

view full answer...

Answer 6

I attached links to this page that have all of the dimensions for the Fulton F2 Trailer Winch #FW32000101 that you referenced. When looking at it from the front the winch will have an overall width of 14.77", which includes the extension from…

view full answer...

Answer 7

The Replacement Brake Disc Assembly part #DL304422 is not included with the Replacement Brake Spring Kit part #DL5703160. These are separate parts for the Dutton-Lainson StrongArm Electric Winch (SA12015DC) part #DL25040.

view full answer...

Answer 8

We do have a lift kit for your Lippert 7K torsion axle but the Dexter Torflex Lift Kits like part #K71-725-02 are designed to fit specific Dexter torsion axles. For example, the above mentioned kit will only fit a #12 Torflex axle that has a 5,500 -…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...