What Modifications Need to Made on 2012 Honda Ridgeline to Install a Curt Front Mount Trailer Hitch

Question

Question:

What modifications need to be made on 2012 model to install hitch?

asked by: Klaus W

0

Expert Reply:

To install the Curt front mount hitch # 33328 on a 2012 Honda Ridgeline, trimming of front air dam or fascia may be required. The instructions that I have linked for you shows what needs to be trimmed. I have also included a picture that shows what needs to be trimmed.

expert reply by: Michael H

0

click to enlarge

Answer 1

Hey Dean, the Detail K2 Elite Snowplow part #K2AVAL8219ELT that you referenced comes with all of the electrical components it will need to install. It wires to the vehicle battery as well as comes with a wired switch that you would run to the cab of…

view full answer...

Answer 2

The Detail K2 Elite Snowplow for 2" Hitch, #K2AVAL8219ELT on your 2017 Nissan Frontier uses an electric actuator raise and lower the plow whereas the Detail K2, #K2AVAL8219 uses an electric winch. The Detail K2 Elite Snowplow, #K2AVAL8219ELT has…

view full answer...

Answer 3

The Detail K2 Avalanche Elite Snowplow part #K2AVAL8219ELT has a 82" wide x 19" tall which is raised and lower via an electric motor which is attached to a set of chain links. In order to use this on a 2002 Jeep TJ you will need the Curt…

view full answer...

Answer 4

The SnowBear snow plows have two mounting options on your 2019 Ford F-250. One is the brackets #K281530 and the other is the Curt Front Mount Trailer Hitch #C31078. I would choose the front mounted hitch since it will allow you to use other…

view full answer...

Answer 5

For your 2013 Honda Pilot I would recommend the Curt Front Mount Hitch #C31064. This hitch has been confirmed to fit your vehicle and should work very well. I attached installation instructions for this product for you to check out also. We never…

view full answer...

Answer 6

For your 2005 Honda Pilot we have the Curt hitch part #33328 as a confirmed fit. I attached a link to install instructions for this hitch for you to check out as well. I also uploaded a picture I took from the install instructions that shows the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

What Modifications Need to Made on 2012 Honda Ridgeline to Install a Curt Front Mount Trailer Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching