Does 2019 Dodge Challenger Curt Hitch 12064 Fit Quad Tip and Non-Quad Models

Question

Question:

2019Dodge Challenger. I am interested in the curt c12064. I currently have stock exhaust but may convert to quad exhaust. You list the same part # c12064 for two different applications except quad exhaust and one with quad exhaust. I am confused?

asked by: Ron F

0

Expert Reply:

I apologize for the confusion, but basically the Curt hitch part # C12064 fits both the the quad tip and non-quad tip versions of the 2019 Dodge Challenger so it will fit and work well for you.

I attached an install video link to this page plus a picture of what it looks like installed for you to check out too.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I went out and took the measurement on both hitches for you. The Draw-Tite, part #76145, measures about 9 inches from the top of the wings where the hitch mounts to the vehicle's frame to the bottom of the collar around the receiver opening. The…

view full answer...

Answer 2

The Curt Trailer Hitch Receiver part #C13236 weighs around 32 lbs and the Curt Trailer Hitch Receiver part #C12064 weighs about 26 lbs. The Curt C12064 is a 1-1/4" hitch receiver and the Curt C13236 is a 2" receiver. I normally recommend a…

view full answer...

Answer 3

Based on our research the top of the inside of the Curt Trailer Hitch #C13236 is going to be about 11-3/4" off of the ground when installed on your 2018 Chrysler 300C. To determine the best ball mount height to keep your towing setup level you…

view full answer...

Answer 4

Thanks for the photo, and the rear diffusers on your 2020 Dodge Challenger would have to be removed in order to install a hitch like the Curt Trailer Hitch Receiver #C13236 which fits your car. Based on the photo, the diffusers go under the bumper a…

view full answer...

Answer 5

I have included a picture showing what Curt trailer hitch #C13236 looks like installed on a 2017 Dodge Charger. I think that the hitch and its positioning match the lines of the vehicle quite well which is not normally the case with trailer hitches.…

view full answer...

Answer 6

For the Curt Class III Trailer Hitch #C13093 on your 2013 Chrysler 300, you will not need to use any specific ball mount. The ball mount you will want to use is the one that provides the correct rise or drop needed for you to tow your trailer level.…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Does 2019 Dodge Challenger Curt Hitch 12064 Fit Quad Tip and Non-Quad Models

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching