Curt Trailer Wiring Harness that Fits 2011 Honda Accord Crosstour

Question

Question:

Will this part# fit a 2011 Honda accord cross-tour? Im assuming all connections would but Im not sure if the cross-tour is a longer vehicle.

asked by: CHARLES P

0

Expert Reply:

We have a custom fit Curt trailer wiring harness that fits your 2011 Honda Accord Crosstour with the part # 56008 but the # C56011 is not the correct fit.

expert reply by: Jameson C

0

Answer 1

First you are going to want to have a EcoHitch Hidden Trailer Hitch Receiver #306-X7286 installed on your 2009 Honda Fit Sport. As you mentioned you are not very handy you can use the link I put near the bottom of the page to search for installers…

view full answer...

Answer 2

For your 2012 Honda Fit I recommend the #306-X7286 EcoHitch Trailer Hitch Receiver. This Class II hitch has a 2" receiver opening with a maximum gross trailer weight of 2,000 lbs and tongue weight of 300 lbs. As for the 2015 hitch, a hitch from…

view full answer...

Answer 3

The only option for a 2" hitch on your 2010 Honda Fit is the EcoHitch Hidden Trailer Hitch Receiver item #306-X7286 you were looking at. This hitch only has a 200 lbs tongue weight capacity. So long as your bike rack and heavy e-bikes weigh…

view full answer...

Answer 4

The Curt T-Connector Vehicle Wiring Harness, part #C56011 is designed to work with your Honda Fit to tow a trailer behind the vehicle. This harness is not designed for operating the lights on your Fit while it is being towed. For that you would need…

view full answer...

Answer 5

The Curt hitch #C11002 for the 2012 Honda Accord Crosstour is going to be visible below the rear fascia as you can see in the picture I have provided. What I recommend is EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - 2" #306-X7299. This…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Curt Trailer Wiring Harness that Fits 2011 Honda Accord Crosstour

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching