Distance Between Mounting Holes of LED Trailer Tail Light # DG52448PB

Question

Question:

I’m looking at DG52448PB taillight it has the dimensions but I need to know how far the screws are apart?? Thanks b.

asked by: Bruce

0

Expert Reply:

The mounting holes of the LED Trailer Tail Light # DG52448PB that you referenced are separated by 7-9/16 inches.

I attached a review video that has more info/dimensions for you to check out as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I have some reverse light options for you but the oval reverse light you show in your photo isn't something we have a direct replacement for. My recommendation is the Great White LED Trailer Back Up Light - 20 Diodes - Clear Lens #PE44AR.…

view full answer...

Answer 2

Hello James. The Curt #C13396 hitch that you mentioned will not fit a 2024 land Rover Discovery Sport. This hitch will only fit the 2015-2019 models without 5+2 seating. Unfortunately, we do not offer a hitch for the 2020-current Discovery Sport…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Distance Between Mounting Holes of LED Trailer Tail Light # DG52448PB

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching