Thread Size on Titan Brake Actuator Lockout Solenoid

Question

Question:

What is thread size on the Titan lockout solenoid. It doesnt appear to be 1/8 npt unless threads are bad. Is it metric or 1/8 B straight sorry I forget the letters for this one.

asked by: Tom K

0

Expert Reply:

The Replacement Solenoid Valve for Titan Brake Actuators # T4748800 has 1/8" pipe (NPT) threads on the male end and 3/8-24 inverted seat threads on the female side. I have attached a short installation video for the solenoid valve that you might also find helpful.

expert reply by: Chris R

0

Answer 1

I really wish there was a cheap and easy way to lock out a Titan model 60 actuator but the only way would be with an electric lock out like the part #T4748800. This threads onto the back of your current actuator and once ran to the reverse light…

view full answer...

Answer 2

I believe you meant Titan Model 10, is that correct? If so, the Titan #T4748800 Replacement Solenoid Valve you've looked at would be compatible with your coupler. The solenoid would mount between the master cylinder outlet at the rear of your…

view full answer...

Answer 3

Locking out a Titan Model 60 actuator like the part #T63FR that you referenced requires inserting the lock out tool into the into the slot right behind the portion of the coupler that inserts into the outer casing. I pointed out where in the attached…

view full answer...

Answer 4

While the install instructions link for the #DM5939 does seem to be not working I was able to find a diagram that shows how this installs on a coupler for you to check out that shows how it installs and where.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Thread Size on Titan Brake Actuator Lockout Solenoid

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching