How Does the Half Moon Vent # WHMAV2-WAVT2 Install

Question

Question:

I read the instructions about the vent but does one cut a 3 inch hole in the exterior piece to match the interior piece?

asked by: Susanne

0

Expert Reply:

The vent uses a 3 inch diameter hole in the trailer. The half moon portion is flush mounted to the outside of the trailer. It is not necessary to cut any holes in the vent. The interior trim piece is deep enough that it will pass through the trailer wall and mate up with the raised circular portion of the outside half-moon portion.

The part is also available in black, as part # HMAV2-AVT2. I have edited a photo of this vent in black so that you can more easily see how the vent goes together.

expert reply by: Mike L

0

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Joe, the limiting air pressure factor for the Lionshead Steel Modular Trailer Wheel #LH44ZR that you referenced would actually be the valve stem you put in it. For example the metal valve stem part #AM20906 would be a great option that can handle…

view full answer...

Answer 3

Since heat rises I would at the very least put a set of the Trailer Vents #HMAV2-AVT2 near the top of the trailer to get the hottest air of the trailer out. What you could do for maximum air flow in your trailer is have a set facing forward in the…

view full answer...

Answer 4

Sounds like the brake controller is backfeeding 12 volts onto the brake light circuit of your RV. Check to see if the red wire of the controller is putting out 12 volts when all of the other wires are connected. If so, then the controller is bad and…

view full answer...

Answer 5

The hinge you referenced part #PLR2212-AS would replace what you have now on your horse trailer and the holes would line up. It looks like for your window you'd need a piano hinge that's about 2 feet long, but at this time we do not have any…

view full answer...

Answer 6

Thanks for the pictures and measurements Tim! The Terran Industries 5-Leaf Double Eye Spring item #TX93RJ are going to be the best option to replace your 26.5" long springs. This spring has a 3,500 lbs capacity so it's going to be a solid…

view full answer...

Answer 7

Hey David, the rubber is not replacement in the MORryde CRE3000 kits like the part #MR39ZR. I found one example of a person online who had found some cracks in their rubber and MORryde just went ahead and sent them out all new equalizers. It looks…

view full answer...

Answer 8

Hey Ken, it looks like your 2024 Ford F-150 Lightning has brake controller wiring behind the coin holder. If you pop that out you should find 4 wires that you will use to wire to a controller like the Redarc Tow Pro Liberty part #RED52VR which only…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

How Does the Half Moon Vent # WHMAV2-WAVT2 Install

Product Page this Question was Asked From

Continue Researching