Replacement Spring Bar for Fastway E2 Weight Distribution System # FA94-00-1033

Question

Question:

Hi Jameson, the bar came off on a rough road. I may be looking at the wrong sway bar FA94-00-1033. I went to check and the number on the existing sway bar is Round Bar 94-00-1000. Is this available and I need one.

asked by: Charles M

0

Expert Reply:

Yes you can, the replacement spring bar you need is the part # FA94-02-1099 for the FastWay e2 kit part # FA94-00-1033 you referenced having. For my own personal curiosity did the bar come off while travelling or did you lose it while parked?

expert reply by: Jameson C

0

Charles M.

9/9/2019

Hi Jameson, the bar came off on a rough road. I may be looking at the wrong sway bar FA94-00-1033. I went to check and the number on the existing sway bar is Round Bar 94-00-1000. Is this available and I need one.

Jameson C.

9/9/2019

The only difference between the Fastway weight distribution kits # FA94-00-1033 and # FA94-00-1000 is that the # FA94-00-1000 comes with a shank and the # FA94-00-1033 does not. So the replacement spring bar # FA94-02-1099 would be what you'd need either way. When the bar came off did it go flying? I'd imagine with all of that spring bar tension it would.

Answer 1

Brent, to remove the Replacement Spring-Bar Release Clip for Fastway e2 Weight Distribution Systems with Round Bars #FA94-02-1059 you are going to need to start by getting the lower screw out of the clip which you're going to need to pry out…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Spring Bar for Fastway E2 Weight Distribution System # FA94-00-1033

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching