Trailair Rota Flex Cushioned Pin Box that Fits as Replacement for Fabex 665

Question

Question:

Could you tell me what the bolt hole measurement for the Trailair Rota-Flex 5th Wheel Pin Box - Lippert 1116 - 19,000 lbs. Item # LC176440 are?

asked by: KYLE P

1

Helpful Expert Reply:

The cushioned Trailair Rota-Flex 5th Wheel Pin Box # LC328330 does fit the Fabex 665 that you have now and would work great as a cushioned replacement. While this pin box states it's designed to fit as a replacement for the Lippert 1621 or 1621HD we've found that in general the 1621 and the Fabex 665 are identical.

expert reply by: Jameson C

1

Kyle P.

9/5/2019

Could you tell me what the bolt hole measurement for the Trailair Rota-Flex 5th Wheel Pin Box - Lippert 1116 - 19,000 lbs. Item # LC176440 are?

Jameson C.

9/5/2019

The # LC176440 would not work in your application as it's 1/2 inch wider overall so it would not fit into the frame brackets on your trailer. You'll notice what looks like plates welded to either side of the pin box to allow for the extra width needed. The vertical holes are also 1/2 inch further apart and the horizontal holes are 7/8 inches further apart.

Answer 1

Yes, the TorkLift SuperHitch Original Trailer Hitch Receiver #TLF1002 will fit your 2004 Ford F-250 with the 6-3/4' bed. The Air Lift LoadLifter 5000 Air Helper Springs #AL57291 you found are designed to fit with the B&W fifth wheel hitch…

view full answer...

Answer 2

In order to resist the chucking (fore and aft jarring movement) experienced, the swiveling skid plate is pretty stiff by design. The relatively gentle jarring experienced during hitching will not move the plate much at all but any chucking…

view full answer...

Answer 3

Air Lift has an air bag kit that fits your 2003 Ford F-350 that has the B and W Turnoverball gooseneck hitch installed with the #AL57291. This actually fits the F-250 and the F-350 so it would work well for your truck.

view full answer...

Answer 4

It looks like you might have a Trailair Roto-Flex 5th Wheel Pin Box like #LC328330. I do recommend confirming this by locating the model name of your existing pin box. If this is the case, then to use the Demco Hijacker Autoslide 5th Wheel Trailer…

view full answer...

Answer 5

I have a solution for you, but there are not AirLift airbags available that will work with your B&W Turnoverball #BWGNRK1108 system on a 2006 Ford F-350. However, there is the Firestone Ride-Rite Air Helper Springs - Double Convoluted - Rear Axle…

view full answer...

Answer 6

From Rep at PullRite, you will need to measure from the front edge of your king pin to the leading edge of the king pin plate to identify which you should use with your Rota-Flex 5th Wheel Pin Box and #LC328330. See the attached image I provided with…

view full answer...

Answer 7

Air Lift does have a number of options for suspension enhancement that fits your 2001 Ford F-250 4x4. A good portion of the reason there are so many fits is that there's some overlap from other vehicle fits they had to make for other vehicles…

view full answer...

Answer 8

The Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle #AL57291 is a confirmed fit for your 1999 Ford F-250 and is designed for compatibility with B&W gooseneck hitches. I've attached a video of this installation to assist. This kit will…

view full answer...

Answer 9

The Air Lift rear axle air bag kits that fit on the 2004 Ford F-250 can be seen on the linked page. You can click on the filter to select either 2WD or 4WD to then see products compatible with your truck. All are rated for 5000-lbs of load support.…

view full answer...

Answer 10

The #AL57291 is designed to fit if you have the B&W 1199R or 1105. If your gooseneck hitch is one of these discontinued B&W models then the air bags will work with your 2001 Ford F-250. If it is not one of these B&W models you will be…

view full answer...

Answer 11

The Air Lift LoadLifter kit part #AL88397 which is a confirmed fit for your 2005 Ford F-250 is perfectly compatible with the B and W Gooseneck hitch #BWGNRK1108-5W.

view full answer...

Answer 12

I can tell you the procedure for replacing the jounce stops on the Rota-Flex pin box though the exact replacement parts are not available like you said. They are a rubber compound but the specifics of it I do not know. 1. With Long Needle-nose…

view full answer...

Trailair Rota Flex Cushioned Pin Box that Fits as Replacement for Fabex 665

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching