How Much Ground Clearance Will Be Lost With C31013 Installed On Vehicle

Question

Question:

How much ground clearance is lost?

asked by: Steve S

1

Helpful Expert Reply:

We have not yet had a chance to test fit the Curt Front Mount Trailer Hitch part # C31013 on a vehicle specifically a Toyota Tacoma. So I would not be able to tell you exactly how much ground clearance is lost. However, I went out the warehouse and measured the brackets and they are 5" tall. If you measure 5" down from your frame in the front of the vehicle that is where the hitch will sit.

expert reply by: Heather A

1

click to enlarge

Answer 1

Hello Terran, While we don't have anything custom fit, there is an option, which is a universal weld-on hitch. Since your frame is more than 44 inches outside to outside, we have a pair of options depending on how much drop you need from the…

view full answer...

Answer 2

Hi Tad, Based on the dimensions you provided I recommend going with the Adjustable Width Trailer Hitch Receiver for RVs, 18" to 51" Wide #C13702. This would mount under the frame with the receiver tube sitting roughly 2" below the…

view full answer...

Answer 3

It's not designed to. The Curt Trailer Hitch item #C15312 is custom fit for 2001 - 2010 Sierra and Silverado 2500 and 3500s. The width of the bolt holes is the same as the item #3371801102 as you can see from the dimensional diagrams below.…

view full answer...

Answer 4

I checked with Curt and they told me that the overall width of the Curt front hitch #C31013 is 32.50 inches and the center to center hole dimension is 30 inches.

view full answer...

Answer 5

I checked with Curt and was able to find a couple of diagrams of the mounting bracket and the receiver portion for the Adjustable Width Trailer Hitch Receiver item #13703. I have attached them below. The width is adjustable between 22" and…

view full answer...

Answer 6

I was able to get some dimensions for you on the Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" #C31063. The overall width is 31-1/8 inches. The mounting holes are 29 inches by 10 inches on center. The receiver tube is 8 inches total…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

How Much Ground Clearance Will Be Lost With C31013 Installed On Vehicle

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching