Measurement of Curt Front Mount Trailer Hitch # C31063

Question

Question:

I m about to purchase front hitch PN C31063 for 2000 ranger. Can you possibly email me a top view dimension drawing Thank You

asked by: Jim O

0

Expert Reply:

I was able to get some dimensions for you on the Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" # C31063. The overall width is 31-1/8 inches. The mounting holes are 29 inches by 10 inches on center. The receiver tube is 8 inches total front to back. I've attached a photo to assist.

expert reply by: Jason S

0

click to enlarge

Answer 1

Hello Terran, While we don't have anything custom fit, there is an option, which is a universal weld-on hitch. Since your frame is more than 44 inches outside to outside, we have a pair of options depending on how much drop you need from the…

view full answer...

Answer 2

We have not yet had a chance to test fit the Curt Front Mount Trailer Hitch part #C31013 on a vehicle specifically a Toyota Tacoma. So I would not be able to tell you exactly how much ground clearance is lost. However, I went out the warehouse and…

view full answer...

Answer 3

I checked with Curt and was able to find a couple of diagrams of the mounting bracket and the receiver portion for the Adjustable Width Trailer Hitch Receiver item #13703. I have attached them below. The width is adjustable between 22" and…

view full answer...

Answer 4

Hi Tad, Based on the dimensions you provided I recommend going with the Adjustable Width Trailer Hitch Receiver for RVs, 18" to 51" Wide #C13702. This would mount under the frame with the receiver tube sitting roughly 2" below the…

view full answer...

Answer 5

I checked with Curt and they told me that the overall width of the Curt front hitch #C31013 is 32.50 inches and the center to center hole dimension is 30 inches.

view full answer...

Answer 6

It's not designed to. The Curt Trailer Hitch item #C15312 is custom fit for 2001 - 2010 Sierra and Silverado 2500 and 3500s. The width of the bolt holes is the same as the item #3371801102 as you can see from the dimensional diagrams below.…

view full answer...

Answer 7

Hi David; we don't have a way for you to mail it to us so you will have to identify the hub to find the right replacement. Identifying the hub is pretty easy and will save you money since you won't have to pay to ship a hub. Based on the bolt…

view full answer...

Answer 8

The Curt Front Mount Receiver, item #31352, has a 9,000 Lbs. Max. Line Pull, and lower fascia trimming may be required on some models. The part that may need to be trimmed is the plastic fascia that is attached to the bottom of the chrome bumper on…

view full answer...

Answer 9

The CURT Front Mount Receiver, #C31063, mounts to the bottom of the frame rails on your 2002 Ford Ranger. What I did was I went out to the warehouse and measured the distance from the top of the brackets that mount to the frame down to the bottom of…

view full answer...

Answer 10

Hi Dustin; as long as you measured pictures aren't necessary. However, I can tell you we don't have a hinge kit for a 2" x 4" trailer tongue. I also ran an internet search and could not find one for those dimensions. Unless you are…

view full answer...

Answer 11

Hey Parker, Yep, it sure will; the correct front hitch that does fit your 2014 Ford F-150 Lariat EcoBoost is the following from Curt: - Curt Front Mount Trailer Hitch Receiver #C31068 I went ahead and verified this with Curt for you.

view full answer...

Answer 12

To install the Curt Hitch part #C31068 on your 2014 Ford F-150 with Ecoboost you will need to remove the air dam and then trim a small section of the lower fascia. See photo.

view full answer...

Measurement of Curt Front Mount Trailer Hitch # C31063

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching