LED Load Resistor for 2016 Land Rover LR4 Towing Trailer with LED Lights

Question

Question:

If your camper trailer has a 7-Way you need part # 20142 but if it has a 4-Way or 5-Way flat connector then use part # TR20141 instead. They both offer the same solution for your 2016 Land Rover LR4 it just depends on what you have on your trailer side.

asked by: Bob C

0

Expert Reply:

If your camper trailer has a 7-Way you need part # 20142 but if it has a 4-Way or 5-Way flat connector then use part # C35FR instead. They both offer the same solution for your 2016 Land Rover LR4 it just depends on what you have on your trailer side.

expert reply by: Jon G

0

Bob C.

9/5/2019

If your camper trailer has a 7-Way you need part # 20142 but if it has a 4-Way or 5-Way flat connector then use part # TR20141 instead. They both offer the same solution for your 2016 Land Rover LR4 it just depends on what you have on your trailer side.

Jon G.

9/5/2019

I'm surprised that the Lamp-Out Sensor # 20142 isn't pulling enough power. Instead of swapping out all of your LEDs for incandescent lights an easier solution is to install load resistors like the Putco # P230004A-2 on your lighting circuits. These essentially do the same thing as changing out your lights to incandescent with the benefits being you don't have to find different lighting for your trailer plus you don't have to go through all of those installations. Simply install these with the quick splices or butt connectors and you are good to go!

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

LED Load Resistor for 2016 Land Rover LR4 Towing Trailer with LED Lights

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching