Which Hitch Fits 1994 GMC 3500 with Roll Pan Rear Bumper

Question

Question:

Hello, Which receiver will fit on my 94 gmc dually crew cab with roll pan? Drilling required?

asked by: Raul

0

Expert Reply:

For your 1994 GMC 3500 with a roll pan bumper we have the Curt hitch part # 13942 as a confirmed fit. This fits without drilling as well.

expert reply by: Jameson C

0

Answer 1

The B and W Hitch part #BWHDRH25122 would fit your 1995 Chevy Silverado 3500 if it was built on a cab and chassis model. Which easy way to determine this is to measure the truck frame from outside to outside. If this measurement is 34 inches then you…

view full answer...

Answer 2

Hey Brian! For 7-way wiring to go with your Curt #C15325 the best option is the #20023. This is only a 7-way so you can either use an adapter like #PK12716 or swap out the connector for one that fits a USCAR connection like the Curt Dual Connection…

view full answer...

Answer 3

If your 1989 Chevy truck is a cab and chassis model (these are the ones that come without beds that are then turned into service vehicles, flat beds, and that sort of thing) then hitch #41947 will fit for sure. But apparently, for 1989, Chevy trucks…

view full answer...

Answer 4

Best option would then be to try contacting a Chevy dealer to see if they could possibly look it up online. Due to the age of the vehicle there isn't any info I can find for it. If the truck has a 454 cubic inch engine it looks like it may have a…

view full answer...

Answer 5

Part #C15325 has a maximum gross trailer weight capacity of 16,000 lbs and 17,000 when using weight distribution. The tongue weight capacity is 2,400 lbs and 2,400 lbs when used with weight distribution. This hitch is designed to be used on trucks…

view full answer...

Answer 6

While we do not have a receiver that is specifically designed to work with your 1996 Chevrolet C2500 having the Tommy liftgate, I do have some measurements that may help you determine if one will fit your truck. You will need to measure the height…

view full answer...

Answer 7

For a 1994 GMC dually truck with a roll pan the Draw Tite hitch part #41522 is the correct fit and a great option. This has towing capacity of 5,000 lbs.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Which Hitch Fits 1994 GMC 3500 with Roll Pan Rear Bumper

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching