Replacement Cab Clamp Assembly for Extang Trifecta Tonneau Cover

Question

Question:

I have a 2017 1500 Silverado Truck I do not need the entire replacement Assembly just the clamp Please help Thanks

asked by: Dennis B

0

Expert Reply:

Thanks for your picture from that it looks like you have an Extang Trifecta tonneau cover and are needing a replacement cab clamp assembly part # EX1034. This is the only way to order and replace the part you are needing to replace.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I spoke with my contact at Extang a while back about the install of the front clamp for Trifecta Cover part #EX1034 and he said that you need to disconnect the screws from the crossbow of the cover so that it will drop down and the cab clamp assembly…

view full answer...

Answer 2

None of the methods are super easy. I'd recommend three though you have to remove hinges. This is least invasive, doesn't require cutting the cover, and also doesn't risk damaging cover.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 6

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 7

Hey Matt, Furrion typically has 4 wires running to their thermostats and the Chill Cube Thermostat #LC74DX is no exception. The harness you see with the thermostat would plug into the Chill Cube's controller and has 4 wires to extra wire to to…

view full answer...

Answer 8

There is a wiring kit for a brake controller Preston but it's not going to be a plug and play one. The 2025 Toyota Tacoma does not have a plug in brake controller port. Toyota stopped putting them in after the 2023 model. For your Tacoma, I…

view full answer...

Answer 9

Hello Steve, Welcome to etrailer, I'm glad you found us! You will need to add the Pollak Mounting Bracket #PK12711U separately. The etrailer Trailer Hitch Receiver #e98850 does not include the electrical connector or a mounting bracket for it. It…

view full answer...

Answer 10

If your 2019 Toyota Tundra includes the factory trailer wiring for a trailer it will have a connector under the dash for a Trailer Brake Controller #RED72CR. This Controller #RED72CR does come with the connector for this application. The small…

view full answer...

Answer 11

Hey Dave, welcome back. The 4" diameter washer will need to be installed between the blue SumoSpring and the 1" spacer on the SumoSprings Solo Custom Helper Springs item #SS65FR. The bolt that attaches the SumoSprings and spacers to your…

view full answer...

Replacement Cab Clamp Assembly for Extang Trifecta Tonneau Cover

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching