Which Tripod 5th Wheel Stabilizer Can be Used with an Andersen Ultimate Connection Adapter

Question

Question:

Will this tripod stand accept a ball for Anderson Hitch setup?

asked by: Doris M

0

Expert Reply:

To use a tripod stabilizer with an Andersen Ultimate fifth wheel adapter you'll need to use the replacement ball assembly part # UF19-001057 with an Ultra Fab stabilizer like the part # UF19-950500.

There isn't a way to use the Husky tripod with the Andersen Ultimate.

expert reply by: Jameson C

0

Answer 1

Hello again John; when First Brands took over as the parent company for Bargman they discontinued most of their lights. That includes the direct replacement for the 30-91-010 and 30-91-011. Typically we recommend the the Peterson Trailer Tail Light…

view full answer...

Answer 2

Leaf springs typically have the part #stamped on the strap that holds the leafs together at one end of the shorter leafs, or it is painted on the concave side of the springs. The part number can then be used to determine the capacity of the springs.…

view full answer...

Answer 3

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 4

Hello James. I can definitely point you in the right direction, but the SAE number is not actually a part number, so this is not a good way to look up a specific light. The light in your picture looks very similar to the Optronics LED Side Marker…

view full answer...

Answer 5

I do have an option for you but we don't carry replacement parts for Carrier Air Conditioners. The best option we can offer you is a new unit, the Advent Air Replacement RV Air Conditioner part #ACCAR135 for 13,500 Btu's or part #ACCAR150 for…

view full answer...

Answer 6

We do offer the Optronics trailer light #MC32RB for red and #MC32AB for amber. These lights will be extremely similar to the #MCL31RB that you mentioned, but they are a bit more square on the ends. The mounting holes on the #MC32RB are 3" apart…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Which Tripod 5th Wheel Stabilizer Can be Used with an Andersen Ultimate Connection Adapter

Products Featured in This Question

Continue Researching