What is Bolt Pattern of Dexter Trailer Hub part # 84545BX
Published 06/06/2019
Question:
Thanks for the reply, but I was not clear in my question. What I was looking for was the diameter of the boss that will hold the bearing race and the grease dust cap similar to the answer on a similar part. should be somewhere around 2 and 5/8 inch. see the referenced question below.
asked by: Marc D
Expert Reply:
Sounds like you are asking about the wheel bolt pattern of the Dexter trailer hub part # 84545BX. This has a bolt pattern of 5 on 4-1/2 inch which is the most common 5 bolt pattern for trailer wheels.
I attached a picture and link for more info on bolt patterns for you to check out as well.
Product Page this Question was Asked From
Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2
- Trailer Hubs and Drums
- Idler Hub
- Standard
- L68149 / L44649
- Standard Grade
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: B&W Tow & Stow 2-Ball Mount - Compatible with GM MultiPro Tailgate - 2.5" Hitch - 18K
- Search Results: st205/75r15
- Shop: Trailer Wiring
- Search Results: ts20037
- Search Results: leaf springs
- Shop: Demco Trailer Coupler - Cast - Adjustable Channel - eZ-Latch - Black - 2-5/16" Ball - 21K
- Search Results: swivel jack
- Search Results: ladder rack
- Search Results: trailer ladder rack
- Shop: Demco 2-Bolt Channel Mount Coupler Hardware Kit
- Shop: 2-5/16" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Search Results: rivets
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Rack'Em Fitz-All Enclosed Trailer Ladder Rack
- Shop: Gooseneck Hitch
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Trailer Hitch
- Shop: Vehicle Tow Bar Wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Can Different Brand Electric Trailer Brakes be Used on a Dexter Axle
- Q&A: Replacement Trailer Hub Assembly for Dexter 8-248 Hubs
- Video: Hands-On with the BulletProof Hitches Extreme Duty Coupler Lock
- Video: A Closer Look at the Dexter Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles
- Q&A: Diameter of Outside Center Hub Bore for Dexter 3,500 lb Idler Hub # 84655UC1
- Q&A: Tire and Wheel Size to Replace 18.5x8.5-8 on Trailer
- Video: Let’s Check Out the Conventional Ramp Door Spring for 8' Wide Enclosed Trailer
- Video: Review of M-3 and Associates Trailer Ramp Springs - Dual Spring Ramp Door Spring - M386FR
- Video: Feature Review Conventional Ramp Door Spring for 5' Wide Enclosed Trailer
- Video: Conventional Ramp Door Spring for 4' Wide Enclosed Trailer Feature Review
on Trailer Hubs and Drums
Marc D.
6/6/2019
Thanks for the reply, but I was not clear in my question. What I was looking for was the diameter of the boss that will hold the bearing race and the grease dust cap similar to the answer on a similar part. should be somewhere around 2 and 5/8 inch. see the referenced question below.