Replacement Brake Hose for Dexter 8K Torsion Axle

Question

Question:

Im looking for a brake hose for a 8k dexter axle with dual caliper hydraulic disc brakes what hose do I need

asked by: Toby

0

Expert Reply:

Thanks for the photo. If the line/hose you are referring to is the one that goes from the caliper to the bracket on your torsion axle you will need to use the Hydraulic Flex Hose part # 18018-SF.

expert reply by: Conner L

0

click to enlarge

Answer 1

If you wanted an exact replacement for the hose you have we do have the part #18018-SF available that would work well for you. That being said the part #BH-3MFS90FF-1-5 you referenced has the same fitting size on both ends of 3/8-24 so it would also…

view full answer...

Answer 2

Indirectly yes, the part #T0778500 does get used with brake hoses. If you check out the attached picture you'll see that holds a union tee that hoses run to. We do have clamps that were designed to secure brake lines like with the part #A0500 for…

view full answer...

Answer 3

First, on kit #80910-T, one end of the flexible hose attaches directly to the brake assembly. You will then route the other end to the steel brake line and use the metal piece with the flared ends to go from the flexible hose to the steel brake line.…

view full answer...

Answer 4

You can tack or spot weld on the Titan flexible brake line tubing bracket #T0776300 if you wanted to. If welding to a dissimilar metal be sure to have a professional welder perform the installation. If it were me I would go the easy way and just use…

view full answer...

Answer 5

For all intents and purposes there is no difference between the part #18018-SF and #BH-3MFS90FF-1-5. They are basically the exact same thing. They are basically two different brands version of the same brake line.

view full answer...

Answer 6

Having the slightly larger main feed line of 1/4 inch is a a great idea for plumbing up your triple axle trailer. We have the HydraStar kit part #HS496-153 which is designed for that. This kit uses 1/4 for the main feed line to the first tee fitting…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Replacement Brake Hose for Dexter 8K Torsion Axle

Product Page this Question was Asked From

Continue Researching