Locking Pins for B&W Tow and Stow To Fit a 3 Inch Receiver Tube

Question

Question:

Will the pins labeled for the 10k and 14k hitches work with the 21k hitch for 3” receivers?

asked by: Glenn

0

Expert Reply:

The B&W Tow & Stow 3-Ball Mount only needs one hitch pin lock, part # WS05 if you have a 5/8" hitch pin hole. The reason for this is that the hitch balls on the B&W Tow & Stow Ball Mount cannot be removed with the ball mount in the receiver tube due to the integrated channel. Therefore, it is not necessary to have locking hitch pins in the adjustment holes.

expert reply by: Conner L

0

click to enlarge

Answer 1

Hey Charles, The Brophy #BH20 has a 13-1/4" from center of hitch pin hole to center of ball hole, which is a bit more than the B&W Tow & Stow ballmounts have so the closest option is going to be the B&W Tow & Stow 2-Ball Mount…

view full answer...

Answer 2

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Douglas! The correct Gen-Y gooseneck pin box for your 2022 Forest River Cardinal Red is the #GY33GR. This fits the Rhino bolt pattern and is rated for trailers with a GVWR of 7,275-16,360 lbs. You will also need safety chains #GY49GR to complete…

view full answer...

Locking Pins for B&W Tow and Stow To Fit a 3 Inch Receiver Tube

Product Page this Question was Asked From

Continue Researching