Do Brophy Camper Tie-Downs HSWB Have a Camper Weight Limit

Question

Question:

What is the camper weight limit for the clamp-on tie downs?

asked by: Bill F

0

Expert Reply:

Brophy Camper Tie-Downs # HSWB do not have a weight rating since they do not support the camper's weight. The truck bed and frame handle that actual camper load and the tie downs provide stability to prevent the camper from shifting in the bed.

expert reply by: Adam R

0

Answer 1

Unfortunately we do not have a video of the HappiJac Truck-Mounted Camper Tie-Downs #LC184089 being installed. The Rear anchors are installed in the end of the bumper. There is no precise mounting location since a variety of bumpers may be installed.…

view full answer...

Answer 2

When picking out Torklift camper tie downs you will need to select whether or not you have a factory or aftermarket hitch. The Curt Hitch part #C15409 would qualify as an aftermarket hitch so you would need to go that route. For your truck you would…

view full answer...

Answer 3

Hi Adam, The Brophy Stake Pocket Mounted Camper Tie-Downs #TDSF don't technically have a weight capacity, though the turnbuckles they need, the Brophy Basic Turnbuckles w/ Hardware for Camper Tie-Downs #TDHP, have a 3,000 lb weight capacity. So…

view full answer...

Answer 4

There is no weight capacity for the Brophy Clamp On Camper Tie-Downs #HSSF. The tie-down hardware kit #TDHP, that is used to secure the camper to the #HSSF tie-downs has a weight capacity of 3,000-lbs. My contact at Brophy said the tie-downs will…

view full answer...

Answer 5

I attached a picture that shows the instructions we have for the Tie Downs part #HSAB that you referenced. We've haven't seen them be an issue on a 2001 Ford F-150, but if you could get me a picture of what your setup looks like I can see if…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Hello Josh, I completely understand where you are coming from. When you need long, equal-length turnbuckles to span about 35 inches on a 2022 F-350 with a Lance 1130, the goal is a setup that fits cleanly, installs easily, and stays secure without…

view full answer...

Answer 11

Hello Mel, great question! Yes, the Torklift tie downs part #TL66FV will fit your 2006 GMC Sierra 2500HD crew cab with the 8 foot bed, provided your truck does not have running boards or cab length boards that extend under the bed, and you are not…

view full answer...

Answer 12

Hey Jack, yes the Torklift camper tie downs part #TL63PR are the correct set for your 2024 Ford F-350 Tremor with a short bed and factory hitch. The turnbuckles part #TLS9526-2 that you referenced as well would be a great set that matches what you…

view full answer...

Do Brophy Camper Tie-Downs HSWB Have a Camper Weight Limit

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching