Replacement Proportioning Valve for RoadMaster BrakeMaster System

Question

Question:

Do u just sell the air valve by its self without the air compressor and tank

asked by: Jose

0

Expert Reply:

It sounds like you are asking if we have the proportioning valve available by itself separate from the RoadMaster BrakeMaster Second RV Kit for Hydraulic Brakes part # RM-98300 and if that is the case then yes, the RoadMaster Regulator Kit part # RM-900001. If this is not the part you are referring to then please just send me a photo of what you need.

expert reply by: Conner L

0

Answer 1

Hey Brian, So I'm sorry to say there isn't a way to add an app or way to wirelessly use the Second Motorhome Kit for Roadmaster BrakeMaster Systems for Hydraulic Brakes #RM-98300. I can see where you're coming from though, as wireless is…

view full answer...

Answer 2

Yes, you can use RoadMaster BrakeMaster Second RV Kit #RM-98300 for motorhomes with hydraulic brakes. The size of the wires coming off the brake light switch should not be a problem but if it's easier you can wire into the brake switch wire going…

view full answer...

Answer 3

In the installation instructions for the Roadmaster BrakeMaster 9060, #RM-98300, they show two fuses wired in to the air compressor circuit. One 20 amp fuse on the power wire of the battery and a 10 amp fuse connected on the blue wire that runs from…

view full answer...

Answer 4

Yes, I spoke with my contact at RoadMaster just to be sure and the LED Display Monitor for BrakeMaster Systems, replacement part #RM-300065-00, is included in the RoadMaster BrakeMaster Second RV Kit for Hydraulic Brakes, item #RM-98300, along with…

view full answer...

Answer 5

On GM vehicles of that vintage, the 12-V pin should be hot regardless of whether the ignition is on or not. If it isn't showing voltage even with the ignition on, you're almost certainly on the right track thinking it's a blown or…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

To convert your M105A2 military trailer to a 7-blade, I would recommend using the Epicord 7-Way with Junction Box #277-000141. This makes the conversion simple and you don't have to worry about wiring the connector itself. You'll also need…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement Proportioning Valve for RoadMaster BrakeMaster System

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching