Height of Timbren # TTORSEQ and Spacers Needed for Lifted Truck

Question

Question:

I am wanting to know how tall the Timbren is with the bracket installed? I have a 2inch lift in the back and am figuring I will need a spacer or two to get my clearance right with the axle. Thanks!

asked by: Dustin

0

Expert Reply:

I went out to our warehouse and measured an overall height with the mounting bracket of 5 inches for the Timbren Rear Suspension Enhancement System # TTORSEQ. Timbren recommends having a 1/2 inch to 1-1/2 inches between the spring and the axle when the truck is empty so if you measure between the frame where your bump stop is mounted and the axle and get greater than 6-1/2 inches you will want to fill that gap with a spacer or two.

We have 1 inch Spacers with # TA25723-90AD00 or 1/2 inch Spacers # TA25722-90F00 available.

expert reply by: Chris R

0

click to enlarge

Answer 1

Hey Chris! Timbren does recommend using the spacers #T33AV on your 2023 Tundra TRD with the factory lift. This will give you the correct gap when installing the Timbren Suspension Enhancement System #T45MR so it engages properly. Are you adding these…

view full answer...

Answer 2

The #AL24JQ will fit your lifted setup on your 2023 Toyota Tundra. However, I would not count on them for off-road use. I'm afraid they would not last and rip off of the end plates. It also would not be covered under their warranty if they were…

view full answer...

Answer 3

To help with the sag of your 2016 Toyota Tundra I recommend going with Timbrens, as they are designed to take the brunt of the added weight when you tow. They will engage when needed to counteract both sag and body roll to help level your truck,…

view full answer...

Answer 4

Hey Ray, yes the Air Lift LoadLifter 5000 part #AL45DQ does fit your 2025 Toyota Tacoma TRD that has the factory lift. I checked with Air Lift and there are no exclusions for the TRD models.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Kent! Your Alliance Avenue already has some great suspension components with the MORryde CRE3000 equalizers, wet bolt kit, and Rota-Flex pin box. I wouldn't replace any of those unless you're experiencing a specific problem. The next…

view full answer...

Answer 8

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Height of Timbren # TTORSEQ and Spacers Needed for Lifted Truck

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching