Timbren 1" Spacer For Raised Frame Vehicles - 1/2" bushing

Ask the Experts about this Timbren Accessories and Parts

• Spacers To Use with Timbren Kit that Fits 2020 GMC Sierra 1500
  You'd need to use the 1/2 inch bushing diameter spacers like the part # TA25723-90AD00 for a 1 inch spacer or # TA25722-90F00 for 1/2 inch diameter with the Timbren kit part # TGMR15MR.
  view full answer...
• Recommended Timbrens for a 2018 Toyota Tundra with 3 Inch Lift Kit
  For your 2018 Toyota Tundra, I recommend using the Timbren Rear Suspension Enhancement System part # TTORTUN4 with three of the Timbren Spacer For Raised Frame Vehicles part # TA25723-90AD00 stacked. Assuming you have a full 3" suspension lift and not a body lift, this option should give you 1/2"-1" of clearance but the spring measures 3-3/4" tall so you can can always measure to be certain. Please keep in mind you will need to obtain longer M10 bolts from your local hardware store to install...
  view full answer...
• What is the Outer Diameter of Timbren Spacer # TA25723-90AD00
  The Timbren spacer # TA25723-90AD00 has an outer diameter of 4 inches. This is a 1 inch version. There is also a 1/2 inch version with the same diameter, # TA25722-90F00.
  view full answer...
• How Many Lift Spacers are Needed for Timbren Springs on a Lifted 2013 Chevy Silverado 1500
  Finding the correct spacer(s) for a lifted truck can be a little tricky sometimes due to the number of lift kits out there. The best way to determine how many spacers you need for the Timbren Suspension Kit, # TGMRCK15S, for your 2013 Chevy Silverado 1500 is to measure the distance from the underside of your frame where your bump stop sits to the axle directly below where the spring makes contact. The spring and bracket in this kit measure 5 inches tall unloaded and the spring should...
  view full answer...
• Where to Install the Timbren Spacer on a 2016 Ram 1500
  If you take a look at the attached photo, the 1" spacer part # A25723-90AH00 for 3/8" diameter hole or part # TA25723-90AD00 for 1/2" diameter hole will need to be placed in between "2" and "3" when using the Timbren Rear Suspension Enhancement System part # TDR1500DQ on a 2016 Ram 1500. Please note that you will need a longer bolt to install the Timbren springs once the spacer is added. You can aquire this bolt at your local hardware store.
  view full answer...
• Height of Timbren # TTORSEQ and Spacers Needed for Lifted Truck
  I went out to our warehouse and measured an overall height with the mounting bracket of 5 inches for the Timbren Rear Suspension Enhancement System # TTORSEQ. Timbren recommends having a 1/2 inch to 1-1/2 inches between the spring and the axle when the truck is empty so if you measure between the frame where your bump stop is mounted and the axle and get greater than 6-1/2 inches you will want to fill that gap with a spacer or two. We have 1 inch Spacers with # TA25723-90AD00 or 1/2...
  view full answer...
• Suspension Enhancement for 2011 Toyota 4Runner with 3.5 inch Lift
  We have suspension enhancement that can fit your 2011 Toyota 4Runner with a 3.5 inch lift but not an air bag setup. Instead you'd need the Timbren kit part # TTORSEQ with lift spacers # TA25722-90F00 for 1/2 inch and # TA25723-90AD00 for 1 inch. You'd need a total of 6 inch spacers and two 1/2 inch spacers. The air bag kits that fit your vehicle fit in the coil of the suspension which there isn't a way to use a spacer with.
  view full answer...
• Spacers for Installing Timbren Rear Axle Jounce Helper Springs in Lifted Ram 1500
  The Timbren rear-axle helper jounce spring kit # TDR1500DQ is a confirmed fit for your 2015 Ram 1500 and when installed the bottom of each jounce spring should sit about 1-inch above your axle when the truck bed is unloaded (and with no trailer hitched). If you do need some we offer 1-inch spacer # A25723-90AH00 which has a 3/8-inch hole and 1-inch spacer # TA25723-90AD00 which has a 1/2-inch hole. You may need to locally source longer bolts. The spring should not contact the axle...
  view full answer...
• Recommended Helper Springs for 2012 Nissan Titan Pro-4X
  I'm really glad you asked because we only have one confirmed fit for the Pro-4x model. It is the Timbren Suspension Enhancement System - Rear Axle # TNRTTNB which is a jounce style enhancement rated for 6,000 lbs load support. It will give you a progressive support as it provides additional support as needed to increase stability while reducing body roll and vehicle sag. It will not change the factory ride when not hauling a load, but will engage as needed for payload and towing.
  view full answer...
• Can Timbren Rear Suspension Kit Fit 2017 Ford F-150 Raptor with 1 inch Lift
  Most block lift kits just lift the body of the truck and not the suspension as well. This is known as a body lift. Suspension lifts are when the distance from the frame and truck axle increase. If you have a body lift the Timbren kit part # TFR1504R fits without any modification. If you added 1 inch to the distance between the truck frame and axle you'd need the part # TA25723-90AD00 for each side and you'd be set.
  view full answer...
• How To Prevent Sag While Towing with a Lifted 2012 Nissan Xterra
  I do have an option for you but the SumoSprings Solo Custom Helper Springs part # SSR-210-47 are not the best option for a lifted vehicle because they don't come with spacers nor are they offered separately. The option to make your own spacers is certainly possible however, if you use the Timbren Suspension Enhancement System part # TJRC01 which is a very similar kit you can use a combination of both part # TA25723-90AD00 and part # TA25722-90F00 until you get the gap down to 1/2"-1-1/2"....
  view full answer...
• 2018 Jeep Rubicon Unlimited Suspension Enhancement Recommendation
  The Timbren suspension kit part # TABSJRJK that you referenced would be the correct enhancement kit for your 2018 Jeep Rubicon Unlimited but since you also have a lift kit you'll need spacers: 1/2" Spacer - # TA25722-90F00 1" Spacer - # TA25723-90AD00 Since you have a 2.5 inch lift you'll need 2 one inch spacers and a 1/2 inch spacer per side.
  view full answer...
• Rear Helper Springs for a 2006 Toyota 4Runner with 1 Inch Rear Lift Kit
  If you are getting a lift kit on your 2006 Toyota 4Runner then air bags that fit inside the coil springs are not going to work. There are no spacers to make up for the additional space created by the lift kit for the coil spring air bags. The exception is if you were to have a body lift instead of a suspension lift since in that case there would not be any extra space. There are spacers available for the Timbren systems though so I recommend going with # TTORSEQ. If the lift kit does...
  view full answer...
• How to Prevent Sag While Towing with a Lifted 2013 Toyota FJ Cruiser
  As long as you are using the factory coil springs on your 2013 Toyota FJ Cruiser then the 2-1/2" lift kit you have in the rear will not be a problem. If you have a set of taller/stiffer aftermarket coil springs then you would need to test these for yourself as the manufacturer does not test fit with aftermarket coil springs, just the factory ones. If it turns out that you do have aftermarket coil springs and the airbags won't work then we still have an option for you in the Timbren Rear...
  view full answer...
• What Is the Correct Size Timbren Spacer for a 2018 Ford F-150
  The Timbren Rear Suspension Enhancement System for your 2018 Ford F-150 is part # TFR1504E which uses an M10 bolt to attach the spring to the bracket. Therefore, you will need to use the Timbren Spacer part # TA25722-90F00 for 1/2" or part # TA25723-90AD00 for 1" which both have a 1/2" bushing.
  view full answer...
• Recommended Timbren Rear Suspension Enhancement for 2015 Jeep Wrangler Unlimited with 4
  We have spacers that you can add to accommodate a 4" lift on your 2015 Jeep Wrangler Unlimited, but there are no Timbren kits available that come preset for a 4" lift. If your Wrangler Unlimited is a 4WD then I recommend going with the Timbren Rear Suspension Enhancement System # TJRJK. If you have a 2WD then you will want the part # TABSJRJK instead. You can accommodate your lift by choosing a combination of the following spacers for raised frame vehicles: 3/8" Bushing 1/2" Spacer...
  view full answer...
• Suspension Enhancements for a 2015 Toyota 4Runner with Taller Rear Coil Springs
  In order to make sure that we get the correct Firestone Coil-Rite Air Helper Springs for you I would need you to take a few measurements. The measurements I would need are the inside diameter of the coil spring as well as inside height while the vehicle is sitting at ride height and the bump stop is removed. Once you obtain this information I would then be able to make sure you get the correct kit. Unfortunately, I wouldn't be able to offer any recommendations without these measurements....
  view full answer...
• Timbren Rear Springs and Spacers for Lifted 2019 Ram 1500 2wd New Body Style Bighorn
  The Timbren Rear Suspension Enhancement System # TDR1500DQ has an overall height of 5-1/2 inches as you can see at the 1:45 minute mark of the attached video. For spacers you can use Timbren 1" Spacer For Raised Frame Vehicles - 1/2" bushing # TA25723-90AD00 or 1/2 inch spacer # TA25722-90F00. This will require a longer 10mm bolt grade 8 for any additional height. You don't want the complete distance to be filled with the spring and spacers because it will give you a rough ride when there...
  view full answer...
• Recommended Front Suspension Enhancement to Reduce Bounce and Hop on 1976 Ford F-250 4x4
  It sounds like the additional weight on the front of your truck when decelerating is an issue. It sounds like the rear of your truck has the additional support but the front of your truck would benefit from suspension enhancement. I recommend the Timbren Front Suspension Enhancement System # TFF2504 which is the only fit we have for your 1976 Ford F-250 4x4. This will help absorb road shock and improve the stability of your truck.
  view full answer...
• Lifted Truck Still Sagging with Equal-i-zer Weight Distribution System
  The adjustments for the Equal-i-zer Weight Distribution Systems like part # EQ37120ET will pertain to adding and removing washers from the head to try and get the spring arms as parallel with the trailer frame as possible. However, this may not completely level your vehicle. The majority of these systems are only designed to gain back half of what you lost and since your vehicle is lifted, there is an even greater chance that the vehicle will not be completely level. If you still seek...
  view full answer...
• Suspension Enhancement for 2017 Toyota 4Runner With 2 Inch Lift
  I checked with Firestone, and spacers are not compatible with their Coil-Rite Springs like part # F4135 that fits your 2017 Toyota 4Runner. There is suspension enhancement you can use however, which is the Timbren Rear Suspension Enhancement System # TTORSEQ. For a 2 in ch lift you would also need a pair of the Timbren 1" Spacer For Raised Frame Vehicles # TA25723-90AD00. I've added links to some video reviews for you to check out as well.
  view full answer...
• Timbren Suspension Enhancement Compatibility for Lifted 2017 Ram 1500
  The Air Lift AirLift 1000HD Air Helper Springs for Coil Springs - Rear # AL60818HD is a great product for your 2017 Ram 1500 but it doesn't account for the lift. The Timbren Rear Suspension Enhancement System # TDRTT1500 will work for your truck but you will need to use spacers to account for your lift if it is a suspension lift and not a body lift. The Timbren 1" Spacer For Raised Frame Vehicles - 1/2" bushing # TA25723-90AD00 and the Timbren 1/2" Spacer For Raised Frame Vehicles - 1/2"...
  view full answer...
• Spacers to Use Timbren Helper Springs on a 2004 Yukon XL Denali AWD with 3-1/2 Inches of Lift
  The spring itself from Timbren kit # TGMRG25C is 5-1/8 inches tall. There is another part of the assembly but it will sit up inside the bump stop cup. If the overall lift is 3-1/2 inches then you will likely want to get a total of 6 of the 1 inch spacer # TA25723-90AD00.
  view full answer...
• Can Timbren Suspension Enhancement Install on Truck with 3-1/2 inch Lift
  Timbrens like the part # TGMRCK25D can be installed on vehicles with lifts like your truck that has a 3.5 inch lift but you have to also buy spacers to take up the additional space created by the lift. Timbren spacers are sold in 1 inch increments and 1/2 inch increments. For a 1 inch spacer you'd need the # A25723-90AH00 and then for 1/2 inch part # TA25723-90AD00.
  view full answer...
• Will the Timbren Rear Suspension Enhancement System Part # TDR1500DQ Fit a Lifted 2014 Ram 1500
  Yes, you can still use the Timbren Rear Suspension Enhancement System part # TDR1500DQ on your lifted 2014 Ram 1500 you just need to add the Timbren 1" Spacer For Raised Frame Vehicles part # TA25723-90AD00 to compensate for the lift. This spacer will be installed between part TA25723-90AD00 (2) and TA25723-90AD00 (3) in the attached photo. You may or may not need to trim the spacer to fit inside the cup. A longer M10 bolt however will most likely be needed.
  view full answer...
• Will the Timbren Suspension Enhancement Work on my Lifted 1998 Chevrolet Suburban?
  You can in fact use the Timbren Rear Suspension Enhancement System part # TGMRSB4 on your lifted Suburban. They have spacers specifically designed for this situation. They are available in 1' and 1/2" sizes and the trick is to get the Timbren to sit between 1/2" to 1 1/2" off of the axle. All lift kits are different so to tell you exactly what you will need is impossible. But you will a couple for sure. Timbren 1" Spacer For Raised Frame Vehicles part # TA25723-90AD00 Timbren 1/2" Spacer...
  view full answer...

Do you have a question about this Accessories and Part?