How To Wire the Hopkins Flat-Tow Harness and Roadmaster InvisiBrake Toghter On a 2016 Jeep JKU
Updated 05/01/2019 | Published 04/30/2019 >
Products Featured in This Question
Question:
I purchased the Hopkins wiring kit, Roadmaster Brake Lite Relay kit, and the Roadmaster Invisibrake. Im assuming that all these need to connect together at some point, most likely at the front of the Jeep where the bracket on the base plate is located. Is that correct? Ive watched the videos for all three, but I didnt see how they integrate with each other!
asked by: Jim
Expert Reply:
For starters, there is no bridge between the toad and the tow vehicle for the Roadmaster Brake-Lite Relay Kit for Towed Vehicles part # RM-88400. This gets installed solely on the toad. In regards to the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles part # HM56200, the Roadmaster InvisiBrake Supplemental Braking System part # RM-8700, and the RoadMaster 7-Wire to 6-Wire Flexo-Coil Kit part # RM-146-7 there are going to be components that gets bridged to the tow vehicle.
The 4-way connector on the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles will need to be removed and then you can install the 6-way and bracket that came with the RoadMaster 7-Wire to 6-Wire Flexo-Coil Kit. I don't know what base plate kit you have but there might be a spot for the above bracket. This will complete the link for these two components. However, if you like you can use one of the pins on the 6-way for a charge line, the Roadmaster Battery Charge Line Kit for Towed Vehicles part # RM-156-25.
The Roadmaster InvisiBrake Supplemental Braking System will then be tied into the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles using the attached diagram. There is also a breakaway cable that gets run to the motor home as well.
Product Page this Question was Asked From
Roadmaster Brake-Lite Relay Kit for Towed Vehicles
- Flat Tow Brake System
- Brake Light Relay
- Roadmaster
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Vehicle Tow Bar Brake System
- Search Results: brake light relay flat tow brake system
- Search Results: trailer breakaway cable
- Search Results: rm88400
- Search Results: vehicle tow bar brake system
- Shop: Roadmaster Stop Light Switch Kit
- Shop: Vehicle Tow Bar Wiring
- Shop: TowTether Breakaway Trailer Safety Cable - Stainless Steel - Qty 1
- Shop: Roadmaster InvisiBrake Flat Tow Brake System - Preset
- Video: Checking Out the Replacement Cable for Roadmaster InvisiBrake Flat Tow Brake System
- Video: Installing the Roadmaster InvisiBrake Flat Tow Brake System on your 2014 Jeep Wrangler
- Shop: Roadmaster Brake-Lite Relay Kit for Towed Vehicles
- Shop: Trailer Wiring
- Shop: Roadmaster Falcon 3HD Tow Bar for Blue Ox Base Plates - 10,000 lbs
- Shop: Rubber Bumper - 1"
- Q&A: Is the Invisibrake System Compatible w/ a Factory Flat Tow Harness on a 2021 Jeep Wrangler JLU
- Q&A: Install Video For Roadmaster InvisiBrake in a Jeep Wrangler
- Q&A: Identifying Correct Motorhome Brake Wire To Tie Into Indicator Light For Roadmaster InvisiBrake
- Q&A: Do I Need A Brake Light Relay To Install The Invisibrake On A 2014 Jeep Wrangler?
- Q&A: Where To Splice The Roadmaster InvisBrake Into The Tail Light Wiring Harness On A 2019 Jeep Wrangler
- Shop: Curt RVibrake 4 Portable Flat Tow Brake System - Wireless Monitor - Proportional
- Video: Let’s Check Out the Roadmaster Universal Braking Monitor for Flat Tow Brake Systems
- Video: Checking Out the Roadmaster InvisiBrake Flat Tow Brake System
- Shop: Floor Mats
- Video: An In-Depth Look at the Rubber Bumper
- Q&A: Are Extra Diodes Needed to Use InvisiBrake with Hopkins Harness on 2015 Jeep Wrangler Unlimited
- Q&A: What is Typical Life of Roadmaster Tow Bar
- Video: Checking Out the Roadmaster Hy-Power Diode
- Video: An In-Depth Look at the Roadmaster Stop Light Switch Kit
- Search Results: tow bar


