Trailer Jack with Outer Tube Diameter Closest to 1.9 inch.

Question

Question:

Trailer is 1967 and current Jack has 1.9inch outer tube diameter.

asked by: Ken

0

Expert Reply:

1.9 inch is going to be a bit too small. Would 2 inch work? That's the closest we have like the Dutton Lainson part # DL22530 that you referenced. Maybe you could enlarge the hole with a dremel type grinder.

expert reply by: Jameson C

0

Answer 1

Hey Phil, If you're looking for the factory wire harness for a plug and play connection you'll find a connector that's gray with a red/orange center like the plug on the Curt Custom Wiring Adapter for Trailer Brake Controllers #C51436.…

view full answer...

Answer 2

It looks like Trailer Hub and Drum Assembly - 5,200-lb Axles - 6 on 5-1/2 Item #8-201-5UC3 could be the right replacement for you. You can check the bearing numbers if you still have the bearings. If they are 25580 for the inner and LM67048 then this…

view full answer...

Answer 3

Past customers have told us the AL-KO 8460 uses inner bearing 25580 and outer bearing 15123, which would make the Timken Bearing Kit #TMK82VR the correct replacement bearing kit for that hub. If you are looking to replace the hub entirely the correct…

view full answer...

Answer 4

We do not have any wheel studs that match what you are needing exactly. The closest that we have are the Replacement Trailer Hub Wheel Stud #RG03-080 that you have already discovered.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Trailer Jack with Outer Tube Diameter Closest to 1.9 inch.

Product Page this Question was Asked From

Continue Researching