Replacement Pin Recommendation for Fastway Weight Distribution System

Question

Question:

Will this fit a Hopkins breakaway controller?

asked by: Craig C

0

Expert Reply:

The only replacement pin I can recommend for a Hopkins breakaway kit is the part # HM20012.

If you wanted the coiled design of the Fastway kit you'd need to replace the switch too with the part # FA80-00-2040 and you'd be set. While the pins aren't all universal between brands we've found that the switches are.

expert reply by: Jameson C

0

Answer 1

It is possible to move a trailer by just attaching to it's safety cables. Most people would avoid the method you described as the trailer will slam into the back of the tow vehicle while stopping. Basically it wouldn't be a thief's ideal…

view full answer...

Answer 2

Hey John, thanks for the pictures an the information. To replace your 072-099-00 leaf spring you'll need the 26" Long 6-Leaf Double-Eye Spring for 4,500 lbs Trailer Axles item #e27SR. When you swap out your leaf springs, you'll also want…

view full answer...

Answer 3

Hey Chuck, usually this is a shock problem with surge actuators. The shock isn't allowing the coupler inner member to go all the way forward and release the hydraulic pressure. We have replacement shocks but I would need to know which actuator…

view full answer...

Answer 4

Thank you so much for the picture and the dimensions, that is exactly what I needed to find you a replacement stud. I recommend the Trailer Hub Wheel Stud - Drive In - 1/2" Diameter x 2" Long item #7-122. I have attached a diagram showing…

view full answer...

Answer 5

Yes, Greg, it’s a nice match for Equal-i-zer bars. The notched tray on the MORryde EzStor Lite Rack for WDH #MR72ZV fits standard 4-point sway bars like Equal-i-zer just fine. Just drop the bars in and they’ll rest securely until you’re ready to hook…

view full answer...

Answer 6

Hey there Leighanne, that's a great question. Luckily, the Weigh Safe Flap Jack Folding RV Stabilizing Block #WS63ER does not have any stipulations as far as long term storage goes. They hold up well in the weather and elements, and have a weight…

view full answer...

Answer 7

Hello again Joel; I would recommend the Curt Air Ride 5th Wheel Pin Box #LC158778 over the Flex Air #LC369535. The pivoting head from the Flex Air causes too much movement so it actually isn't compatible with the Andersen hitch. Since the Air…

view full answer...

Answer 8

To determine if the MORryde Cushioned 5th Wheel Pin Box for 14K to 18K Trailers w/ Lippert 1621 and 1621HD #MR84VR will fit your trailer you'll need to first determine your trailer's bolt pattern. There will typically be a sticker (pictured…

view full answer...

Answer 9

The interior lights of your trailer would be powered by the 12 volt accessory circuit on the 7-way of your 2010 GMC Sierra. You will want to check the 1:00 position of the 7-way on your truck with a circuit tester like part #PTW2993 to verify if…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

With you trying to run off of just 12v power you're going to limited to just roof vents with a 12v fan to cooler your horse trailer. There isn't a similar option to the #KH43100 without the heater that would be anything other than a simple…

view full answer...

Answer 12

Between those two color choices the black one would most likely be the ground wire. However, if you hook it up with the black as the ground and it does not work I would recommend trying the red wire. Also, you should trace both of these wires back on…

view full answer...

Replacement Pin Recommendation for Fastway Weight Distribution System

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching