Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
If you're tired of your breakaway switch cable dragging the ground or fraying, this kit is going to be your perfect solution. It features a coiled cord, so there's no need to wrap cable around your trailer frame to prevent dragging.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today you're going to get a good look at and we're going to show you how to install the Fastway Zip Trailer Break Away Switch with coiled cable. It's available in four foot long with part number FA80-00-2040 and in six foot with part number FA80-00-2060. This is a great replacement for your trailer's old break away device. In case of a catastrophic event where you may become uncoupled or disconnected from your trailer, this switch will activate, locking your brakes, bringing your trailer to a slowing halt.The cable is coiled to prevent it from dragging on the ground. It doesn't look thick, but it's actually a high strength woven steel, so it's going to be durable and last for a long time. The vehicle end features a carabiner so it's easy to connect to your safety chain loops.Here at my camper, you can see my old break away switch is junk.
It's just hanging there. We're going to replace it with the Fastway Break away switch. Yours may remove differently, I'm just going to unbolt mine and cut my wires. Now, on this trailer, the wires are run through some loom. I'm just going to reveal them and then cut them where I want to splice into them.
Now I can remove and discard my old break away switch.Now you can set your break away switch in place where you want it. You want to be sure you have enough room to connect your break away to your vehicle. To get it mounted, you'll have to provide your own hardware. We recommend using a self-tapping screw.I've gone ahead and routed my wires through the wire loom material, back to where I cut my wires. If you don't have any loom material and would like some to protect your wires, you can pick some up here at etrailer.com with part number 459075-1, and that's sold by the foot.
Here where my wires meet, as you can see, I've got some excess. I'm going to trim some off. I'm going to be using some butt connectors, so we'll want to be sure and allow for that.Now I'm going to strip back all four of my wires with some wire strippers and I'm going to go back about a quarter of an inch. We'll be using heat-shrink butt connectors. These are not included, but you can pick some up at etrailer.com with part number DW05744-5.
Now since it's a switch, it doesn't matter positive or negative, we can connect either wire to either wire. So we'll first take our heat-shrink butt connector and make sure that that's all the way inside, then I'm going to crimp it. And I'll take one of my other wires and do the same thing. Then I can repeat the same process with my other wire.The reason we're using heat-shrink butt connectors is because we're on the outside of the trailer and we don't want any moisture to get inside. Let's go ahead and shrink those down. We're using a heat gun to do so. Now we'll tuck our wires back into our loom. If you want, you can use some electrical tape.To test it out, you can support one of your axles with a jack stand, then you can get your wheel spinning real good and then have somebody pull out the switch. Go ahead. If it locks up, it works correctly. And now you've had a good look at, and you know how to install, the Fastway Zip Trailer Break Away Switch with coiled cable.
Customer Satisfaction Score:
100% were satisfied with this product
0% of customers were not satisfied
Ratings & Reviews

Paul
10/18/2021
Been very pleased. This completely stopped the problem of the breakaway cord getting caught on things

Paul
10/18/2021
Been very pleased. This completely stopped the problem of the breakaway cord getting caught on things

Derek
10/25/2019
Its still going strong and has been much nicer than the straight cable. I would definitely buy this again.
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.








Paul
10/18/2021
Been very pleased. This completely stopped the problem of the breakaway cord getting caught on things