Hitch Extension Recommendation for 2-1/2 inch Hitch

Question

Question:

Need a ~~12inch long receiver reducer 2.5inch to 2. simply a 2.5inch square tube with 1/4inch walls. 2.5OD, 2.0ID. 10inch min length.

asked by: Chris H

0

Expert Reply:

The closest adapter we have to what you need is the Curt hitch adapter part # C45048. This fits a 2-1/2 inch hitch and provides a 2 inch hitch opening but it's minimum length is 24 inches. The only other pre-drilled option is the part # HR26.

expert reply by: Jameson C

0

Answer 1

Hey Bob, The TorkLift Cannon Hitch Extension #TLE1648 would be a good option if your F-350 has the factory 3" Ford receiver hitch and you're needing 48" of extension. You can measure to figure out the correct length needed, with or…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Hitch Extension Recommendation for 2-1/2 inch Hitch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching