Will the Hands Free Liftgate Feature Still Work on a 2019 Acura RDX with Draw-Tite Trailer Hitch

Question

Question:

I have a 2019 RDX Advance pack front wheel drive. Will the trailer hitch part 76268 stop the use of my kick to open rear hatch.

asked by: Thomas

0

Expert Reply:

The Draw-Tite Max-Frame Trailer Hitch Receiver part # 76268 which is a fit for your 2019 Acura RDX with Advance Package will not impede the use of your hands free liftgate sensors. However, you will need to position your foot to either the right hand or left hand side of the receiver tube opening in order for them to read.

expert reply by: Conner L

0

Diego C.

6/28/2020

Just wanted to double check I saw an expert say that hitch 76268 will not interfere with the tailgate sensor on the 2019 acura rdx? Also is there a sensor relocation kit in the works if it does interfere?

Reply

Chris R.

7/1/2020

Unfortunately it's a little "hit or miss" with regards to the liftgate sensors on your Acura RDX. In most cases the Draw-Tite # 76268 should only interfere to the point of having to move your foot to either side of the hitch receiver, but we have had a couple customers come back and say it completely blocked theirs. The factory location of the sensors can vary just a tad and it only takes an inch or two off to make the difference. You can check with a local Acura dealer about a potential sensor relocation kit but at this time it's not something we have available.

Reply

Answer 1

Hey David congrats on the new SUV! There are two Draw-Tite hitches that fit the 2025 Acura RDX one is a class III 2" and the other is a class II 1-1/4". I have listed them below: 2" Hitch - Draw-Tite item #76268 1-1/4" Hitch -…

view full answer...

Answer 2

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 3

You never have to install load resistors on a trailer when converting the taillights to LED. The only time you have to do that is when converting a vehicle light from incandescent to LED.

view full answer...

Answer 4

The ThinLine LED Tail Light #STL76RB is our closest light to your current tail light. This light is 13-1/4" long, 2-1/8" wide and 1-7/16" tall. It also has 11 LEDs like your current light. For your tail lights you will need to verify…

view full answer...

Answer 5

First, you would want to use 2 of these because otherwise the light would blink with either turn signal. What you you would do is take a trailer side 4-Way, #A35W42B, and attach the lights wires to it as follows: On the driver side you will attach…

view full answer...

Answer 6

I recommend our etrailer Trailer Hitch Receiver #e72AR for your 2024 Acura RDX. This is the same receiver I got for my 2020 RDX and I like how the matte black finish looks against my lower fascia compared to the other receivers which have a gloss…

view full answer...

Answer 7

Hey Kurt, The tech note on the etrailer Trailer Hitch Receiver #e72AR is talking about wheel diameter and not overall diameter of the wheel and tire. Since you have 17" wheels you shouldn't have an issue with a full-size spare.

view full answer...

Answer 8

It is not uncommon for some hitch installations to require spacer blocks of some kind to get the hitch to install properly. If they are required in your situation then it is permissible to use them. A spacer block such as #RP3022 could be used unless…

view full answer...

Answer 9

The Acura MDX is the 'sister' vehicle to the Honda Pilot. The MDX and Pilot typically don't have problems with the hitch interfering with the liftgate sensors. I believe you're thinking about the RDX/Honda CR-V which frequently has an…

view full answer...

Answer 10

We do have a hitch for the Touring model of the 2017 Honda CR-V. It is the etrailer Trailer Hitch item #e98848. This is the only hitch confirmed to fit the Touring model. As far as the foot activated lift gate sensor is concerned there is a…

view full answer...

Answer 11

The Draw-Tite Class III hitch you specified, part #76268 has two holes in each side of the receiver tube. The larger 5/8 inch diameter hole is meant for the hitch pin. The smaller hole is not used. So, in regards to your question-the larger hole is…

view full answer...

Answer 12

I definitely have those measurements! I pulled the Draw-Tite Hitch #76268 from the warehouse and measured it for you. From the front of the hitch receiver tube, the center of the pinhole is 2-3/8". From the rear of the receiver tube, the center…

view full answer...

Will the Hands Free Liftgate Feature Still Work on a 2019 Acura RDX with Draw-Tite Trailer Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching