Dimensions of Replacement Rubber Strips for Crossbars

Question

Question:

What are the measurements, especially of the snap ininch lips? I am looking for replacement rubber strips for car top load bars.

asked by: Helmut M

0

Expert Reply:

The Replacement Rubber Strip for Ladder Rack TH376 # 853-3544-23 fits a channel that is 0.443 inches wide at lip. This is 70-1/2 inches long and is a thicker material.

expert reply by: Jason S

0

click to enlarge

Answer 1

I checked with Thule and for the replacement rubber stripping that goes on the top of the discontinued Thule Xsporter 422 truck rack system they list Replacement Rubber Strip #853-3544-23 as the correct part.

view full answer...

Answer 2

The Replacement Rubber Strip for Ladder Rack TH376 - #853-3544-23 fits a channel that is 0.443 inches wide at lip. This is 70-1/2 inches long and is a thicker material. This strip is just about 1" wide total. I've linked a photo that shows…

view full answer...

Answer 3

We do indeed offer replacement rubber strips that are a specific fit for the underside of your Thule ProBar crossbars. They're available as part #TH67FQ. They measure 80 inches long and are sold individually.

view full answer...

Answer 4

The correct channel cover you need for your older Thule Xsporter Pro Adjustable Height Truck Bed Ladder Rack is the Replacement Rubber Strip for Ladder Rack part #853-3544-23. I called my contact at Thule to confirm this.

view full answer...

Answer 5

The Replacement T-Bolt, item #853-0782, is an M-8 size square head bolt. Most of the bolts used on the Thule ladder racks use M-8 size bolts normally, but we do have a M6 x 12 mm Allen bolt for the Ladder Lift, item #919-0612-54. This is used with…

view full answer...

Answer 6

I spoke with a representative of Thule, who told me that they did not classify the 450 lb weight capacity of the Thule XSporter #TH500XT as either static or dynamic and that you only needed to have a capacity of less than 450 lbs and you would be…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Dimensions of Replacement Rubber Strips for Crossbars

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching