Replacement Shank Assembly 8880580 Fit on Older Yakima HoldUp Hitch Bike Rack
Updated 05/21/2020 | Published 12/27/2018
Question:
Hello, does the 8880580 tongue fit the rack in the picture? It is an old Holdup rack. Yakima. Thanks.
asked by: Derek B
Expert Reply:
Thank you for the photo of your older Yakima hitch bike rack for which you want to confirm the fit of replacement shank/tongue assembly # 8880580.
Yakima confirmed the fit of this part on your rack. You may also need Hitch Bolt # 8890200 to secure the shank to your hitch.
I also went to our warehouse and took a number of measurements that should give you what you need to verify that this part will work on your rack. The linked photo indicates the hole diameters, hole spacing and inside and outside bracket dimensions.
Product Page this Question was Asked From
Replacement 2" Hitch Shank for Yakima HoldUp Bike Racks
- Accessories and Parts
- Hitch Bike Racks
- Shanks and Adapters
- Shanks
- HoldUp
- Yakima
more information >
Continue Researching
- Shop: Replacement 2" Hitch Shank for Yakima HoldUp Bike Racks
- Search Results: replacement yakima pin
- Search Results: yakima hitch pin lock
- Video: Review of Yakima Hitch Adapters - Hitch Reducer - Y74MX
- Video: Checking Out the Yakima Hitch Receiver Reducer Sleeve
- Video: In-Depth Review of the Replacement 2" Hitch Shank for Yakima HoldUp Bike Racks
- Shop: Yakima Hitch Receiver Reducer Sleeve - 2.5" to 2" - 10" Long
- Q&A: Does the Replacement 2" Hitch Shank for Yakima HoldUp Bike Racks Work w/ the Older Gray Ones?
- Shop: Replacement Hitch Bolt for Yakima HoldUp 2, OnRamp, and BigHorn Bike Racks and DryDock Canoe Carrier
- Search Results: yakima hold up 2
- Shop: Replacement Hitch Hardware for Yakima HoldUp Bike Racks for 2" Hitches
- Shop: 2 Bike Add-On for Yakima HoldUp Bike Rack for 2" Hitches - Wheel Mount
- Video: Review of the Replacement Tilt Pull Pin for Yakima HoldUp Bike Racks
- Shop: Replacement 1-1/4" Hitch Shank for Yakima HoldUp Bike Racks
- Shop: Replacement Shank and Pivot Hardware for Yakima BigHorn, BuckHorn, KingPin, or SlickRoc Bike Carrier
- Video: 2-Bike Add-On for Yakima StageTwo Bike Rack for 2" Hitches Feature Review
- Q&A: Replacement Tilt Pin for Yakima HoldUp Bike Rack
- Search Results: shank
- Video: Review of Yakima Replacement Shank And Pivot Hardware - Y8780018
- Shop: Trailer Hitch
- Video: A Closer Look at the Replacement Hitch Hardware for Yakima HoldUp Bike Racks for 2" Hitches
- Q&A: How To Convert Yakima HoldUp for 1-1/4 Inch to 2 Inch
- Shop: RV Covers
- Shop: Truck Bed Bike Rack
- Q&A: Replacement Spine For The Yakima HoldUp
- Q&A: Comparing the Yakima HoldUp and Yakima HoldUp EVO
- Q&A: Converting Yakima HoldUp 2 Bike Rack for 1-1/4 Inch Receiver for Use with 2 Inch Receiver
- Q&A: How to Install the Replacement Latching Spring Pin Part # 8880582
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
on Accessories and Parts
Mike S.
5/18/2020
I am also hoping to use 8880580 on an older HoldUp. The correct full assembly is #8880127 but it is nowhere to be found anymore. Is this tongue likely to be a correct fit for the silver HoldUp spine? Right now I'm using an 2->1.25" adapter, but since I bought a heavy electric bike I hope to have a direct fit to my 2" receiver.