What do Trailer Acronyms GTW and TW Mean

Question

Question:

what is the difference between GTW and TW

asked by: Michael S

0

Expert Reply:

In the trailer world GTW stands for Gross Trailer Weight, and TW means tongue weight.

Gross trailer weight is the entire weight of the trailer and tongue weight is the amount of vertical load that is on the coupler of the trailer. Basically how the vertical weight that the trailer hitch carries.

I attached a help article on determining tongue weight for you to check out as well.

expert reply by: Jameson C

0

Answer 1

There are two options you can use for a bit of added height when using your B&W Turnoverball Underbed Gooseneck Hitch #BWGNRK1016. You can get an extra 1" by using the High-Rise Ball for B&W Turnoverball #BWGNXA2050. You can also use the…

view full answer...

Answer 2

The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 4-Point Set #LC358590 has 4 35-amp fuses located on the controller. Attched is a complete wiring diagram for you to check out.

view full answer...

Answer 3

There are several anti-rattle devices that would be good to use when towing a boat trailer. The construction of your ball mount will determine the best choice for your application. If your ball mount is hollow, and you have a 2 inch receiver hitch,…

view full answer...

Answer 4

The Curt Trailer Hitch Receiver part #13028 is designed to fit the following vechiles: - 88-91 CHEVY/GMC 4 DR CREW CAB ONLY - 73-79 FORD 250 CREW CAB - 73-06 CHEVY/GMC FULL SIZE CAB & CHASSIS w 34" FRAME - 73-06 FORD PICKUP: CAB AND CHASSIS…

view full answer...

Answer 5

Hey Kevin, Thanks for your question! The B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2" #BWHDRH25122 measures 5.4 inches from the top of the frame mounting brackets to the top of the receiver tube. Of all the hitches we…

view full answer...

Answer 6

Hey Keith, thanks for reaching out. At this time there is only one custom fit front hitch made for the 1989 Geo Tracker, the Curt #11128. This has a 1-1/4" receiver though. There is nothing made for that vehicle with a 2" receiver. What…

view full answer...

Answer 7

Hey Mark! For a rating that high that will fit your motorhome you're going to have to switch to a weld-on hitch. The Curt Class 5 Universal Weld-on Hitch #C99CR is going to be the best option here. This hitch still has a 2" receiver and…

view full answer...

Answer 8

Thanks for reaching out, Gregg. I can completely understand wanting to confirm the install details beforehand. Older trucks can definitely take a little more digging than the newer ones. I noticed you were looking at the EcoHitch Front Mount Hitch…

view full answer...

Answer 9

The Curt Trailer Hitch Receiver part #13028 could potentially fit your 1966 Chevrolet C10 with aftermarket bumper. However, I would not be able to confirm this as the trailer hitch is only tested with the OEM bumper. I have attached a photo for you…

view full answer...

Answer 10

Good to hear from you, Ivan! I have 2 different hitch options for your 1985 Chevy C10 pickup depending on what bumper you have on your truck: - Standard/Step Bumper #13028 - Deep drop Bumper #C13099 These are designed to hide the crosstube under your…

view full answer...

Answer 11

Hi Greg; we do carry a hitch and wiring for your 2025 Sienna. The best hitch is the etrailer #e56RR. This has a 2" receiver, bolt-on installation, and a matte black powder coat finish. It also comes with a limited lifetime warranty. For wiring…

view full answer...

What do Trailer Acronyms GTW and TW Mean

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching