Is there a Torque Spec for Installation of Castle Nut on 2,000 lb Axle?
Published 10/24/2018
Products Featured in This Question
Question:
I was wondering what the torque specs are for this bearing as I am trying to have it where the bearing wont go bad within a few uses. If there is any way you guys could help me it would be greatly appreciated. Thank you for taking the time to read this and or respond.
asked by: Christian T
Expert Reply:
The castle nuts do not have a torque spec. Bearings and races are fit to the spindle precisely and will have minimal movement to the washer and castle nut which will simply be tightened and held in place with the cotter pin # 165649. We recommend tightening until the nut stops without added force and then backing it off one notch to fit the castle nut.
The Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings # 8-91-05UC1 is a fit for 1.063 inch spindles and when the grease is packed into the bearings correctly will prevent the bearings from failure. I recommend using the Bearing Packer - Plastic # PTW1218 to ensure proper preparation use grease.
Product Page this Question was Asked From
Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings
- Trailer Hubs and Drums
- Idler Hub
- Standard
- L44649 / L44649
- Standard Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Dexter Trailer Idler Hub Assembly for 2,200-lb Axles - 5 on 4-1/2 - Pre-Greased
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized
- Search Results: 5 on 4~1/2 inch trailer hubs and drums
- Search Results: 1/2 lug nuts
- Shop: Mud Flaps
- Search Results: l44649
- Video: Bearing Buddy Bearing Protectors-BB1980A-SS Spec Review
- Video: Review of the Bearing Kit, L44649 Inner/Outer Bearings, 10-9 Seal
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings
- Shop: Timken Bearing Kit, L44643 Inner/Outer Bearings, L44610 Inner/Outer Races, 204507 Seal
- Shop: Dexter Trailer Idler Hub for 2,000-lb and 2,200-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: Grease Seal - Double Lip - I.D. 1.500" / O.D. 1.987" - 2,000-lb to 2,500-lb Axles - Qty 1
- Shop: Timken Replacement Bearing and Race Set #4 - L44649 and L44610
- Search Results: trailer hubs and drums
- Search Results: 5 on 5 inch trailer hubs and drums
- Shop: Suspension Enhancement
- Q&A: Should Leaf Spring Capacity Match Trailer Weight or Axle Weight for Best Ride Comfort
- Q&A: How Close to Trailer Weight Should Capacity of Trailer Leaf Spring Be
- Q&A: What is the Difference Between Load Range C and D ST175/80D13 Trailer Tires
- Search Results: trailer hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Trailer Hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: Measuring To Choose The Right Trailer Axle
on Trailer Hubs and Drums
