How Tall are Timbren Springs # TJRC01 for a 2014 Nissan Xterra

Question

Question:

Hello, Im looking for a set of helper springs for my 2014 Nissan Xterra S. These should fit a stock suspension, but mine has a small lift, but Im not sure how much. It was on there when I bought the vehicle. Im not seeing a length of these springs listed. Could you get me a length so i can measure and see if they will even contact my axle tube or is there a slightly longer set for another vehicle I may be able to use?

asked by: Shawn R

0

Expert Reply:

The springs in Timbren kit # TJRC01 for your 2014 Nissan Xterra are 3-3/4 inches tall. They also come with 1 inch spacers should you need the additional height. Once installed there should be just a slight gap between the top of the axle and the bottoms of the Timbren springs. I have included a link to the instructions for you.

expert reply by: Michael H

0

click to enlarge

Answer 1

For your 2007 Nissan Xterra I recommend going with the Timbren Active Off-Road Bumpstops #TABSJRC01 that you referenced. These are really designed for exactly what you're needing them for on your Xterra. They will replace your factory bumpstops…

view full answer...

Answer 2

When looking at a Weight Distribution (WD) system you will want to choose one with a Tongue Weight (TW) range that the Total Tongue Weight (TTW) of your towing setup falls in the middle of. To find the TTW of your towing setup you will need to add…

view full answer...

Answer 3

If you are considering Timbrens like the #TDR1500DQ and the SumoSprings like the #SSR-307-47 for your 2022 Ram 1500 4x4, I recommend the SumoSprings #SSR-307-47. The SumoSprings will offer the same quality as the Timbrens in terms of suspension…

view full answer...

Answer 4

I recommend the SumoSprings #SSR-210-40 for your 2010 Xterra 4x4 since you'll be towing and hitting rough roads occasionally. These are specifically designed to provide extra support to your existing springs while maintaining a smooth ride when…

view full answer...

Answer 5

For your 2014 Nissan Xterra 4x4 I recommend the Timbren helper springs #TJRC01. Timbren springs get progressively stiffer the more weight is put on them to better support the vehicle when under load. When not loaded or towing a trailer you may…

view full answer...

Answer 6

I strongly recommend going with the SumoSprings Helper Springs item #SS95GR over Timbren's like item #TNRTTNB for your 4WD 2020 Nissan Titan. Both systems will support your rear end and keep your truck level while towing but you won't notice…

view full answer...

Answer 7

The Timbren #TJRC01 provides the leveling and stabilization you are looking for. These rear axle suspension rubber springs replace your factory original bump stops and require no drilling to install. Typically, we only recommend the front suspension…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

How Tall are Timbren Springs # TJRC01 for a 2014 Nissan Xterra

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching