Torque Setting for 1/2 Inch Trailer Wheel Lug Nuts or Wheel Bolts

Question

Question:

what are proper torque setting for 1/2inch stud on 12inch wheel size trailer hub?

asked by: DAVID W

0

Expert Reply:

On a 12 inch wheel that uses 1/2 inch lug nuts you will need to torque the lug nuts to 75 to 85 foot pounds each. This is the same for steel or aluminum wheels. If the wheel secures to the hub using bolts instead of lug nuts then it would be the same. If you need a torque wrench you can use # ALL944001.

expert reply by: Michael H

0

Answer 1

The largest diameter tire we have that is compatible with a 12 inch wheel is a ST145/R12 size tire which measures 21.3 inches in diameter. For this I recommend using the Kenda Karrier S-Trail #AM10140 which has a load range of E (1,520 lbs at 80 psi)…

view full answer...

Answer 2

The torque spec for your 12" aluminum trailer wheels will come down to the size of the wheel stud and lug nuts. If your trailer uses the standard 1/2" wheel studs and lug nuts then you will want to torque the wheels to 75-85lb-ft. If you…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Torque Setting for 1/2 Inch Trailer Wheel Lug Nuts or Wheel Bolts

Products Featured in This Question

Continue Researching