Troubleshooting No Power at Factory Trailer Wiring Plug on 2014 Nissan Frontier
Updated 10/30/2026 | Published 08/25/2018 >
Products Featured in This Question
Question:
Hi, I just purchased a used 2014 nissan frontier SL with the factory tow package. It has a Curt Custom Fit Vehicle Wiring C55441 harness at the bumper area. The trailer lights dont work. No power at the factory wire harness where the Curt adapter plugs into. The 10 amp fuse is good thats under the front hood. The 30 amp fusible link thats in the same box as the 10 amp fuse is good, also under the front hood. Any suggestions on how to get the light to work? Another way of hooking up the trailer lights? Where would that relay get plugged into? Thanks,
asked by: Norman
Expert Reply:
If you are not getting any power at the factory port where the Curt Wiring Harness # C55441 plugs into, this actually may indicate that your 2014 Nissan Frontier is not equipped with the factory tow package. The existing Curt harness will still plug into the factory port like you see on your vehicle, but without the tow package you will still need to add a relay harness for the port to become active.
This relay harness is included with the Curt T-Connector # C56225. It is not available separately outside of this kit. To install the relay harness you will need to remove the passenger side kick panel to access the factory 12-pin wiring connector that it will plug into. I have attached an image and an installation video to assist.
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: trailer wiring
- Search Results: trailer wiring harness
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Replacement Wiring Harness for Curt T-Connector Nissan Vehicle Wiring Harness with 4-Way Plug
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Trailer Mate Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Brake Controller
- Video: Beginner’s Guide to Installing the Curt Trailer Hitch Receiver on a 2019 Nissan Frontier
- Video: Trailer Wiring Harness Installation - 2016 Nissan Frontier C56225
- Video: Review of the etrailer SD Non-Binding Tow Bar
- Video: Set up: Roadmaster Crossbar-Style Base Plate Kit on a 2022 Jeep Wrangler Unlimited
- Search Results: side wind jack
- Search Results: electric trailer brakes
- Search Results: trailer brakes
- Search Results: vent fan motor
- Search Results: ram jack handle
- Shop: Gooseneck Hitch
- Video: Set up: Curt Relay Kit for Nissan Armada or Titan Aftermarket Tow Package on a 2011 Nissan Titan
- Q&A: No Trailer Running Lights on a 2014 Nissan Frontier
- Q&A: Installing 7-Way Trailer Connector on 2014 Nissan Frontier
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector


Arnold
10/30/2026
I added the relay wire harness under the kick panel plugged in all the wires are all the breakers or whatever they are and I still don't have brake lights