Will Kodiak Wheel Bolt # K12WB169 Fit if There are Small Differences in Size

Question

Question:

It looks like this is the closest fit I can find. It is off of an Extreme Trailer for a Malibu Boat. The letters/numbers on the top of the stud are: 6109 RT A = .5 B = 1.7 C = .315 D = .4795 E = .56 I used a micrometer, but some of them are pretty close. Do you think this part will work, or is there another one that would be better? Thanks!

asked by: Rob

0

Expert Reply:

The Kodiak Wheel Bolt # K12WB169 that you referenced should fit just fine. Since all of the differences are small fractions of an inch you are good to go!

expert reply by: Jon G

0

Answer 1

Can you please let me know the what the diameter of the knurled part needs to be? You can do this by measuring the lug studs you current have with a digital caliper to the nearest hundredth of an inch.

view full answer...

Answer 2

We do have a 1/2" diameter wheel bolt that is close to 1-3/4" long which may work for you. The Kodiak Wheel Bolt #K12WB169 is 1-11/16" long, but that does not take into account the lip of the bolt, as you can see by the accompanying…

view full answer...

Answer 3

I took a look at the wheel lug stud LCI SKU 121803 you mentioned, and I was able to find the Kodiak Wheel Bolt #K12WB2. This bolt is 2" long, and has a thread size of 1/2"-20 UNF-2A.

view full answer...

Answer 4

It sounds like you have a different size axle than anything we carry. The closest we have is the Dexter Trailer Axle w/ Electric Brakes - E-Z Lube - 6 on 5-1/2 Bolt Pattern - 86-1/2" - 5.2K #8327816-EB which has spring centers at 71-1/2 inches…

view full answer...

Answer 5

Hey Larry, I would recommend going with a stainless steel lug nut like the part #LHLR103 that matches the specs you need. Stainless steel won't rust or corrode. This means they won't swell up either making it hard to fit a socket on.

view full answer...

Answer 6

We don't have exact specs on the part that you're referring to, but I do know that's a stamp on a UFP hub, so I was able to reach out to my tech contact at Dexter UFP and he said that most of the hubs that number would be stamped on use a…

view full answer...

Answer 7

Based on the dimensions you listed it looks like the part #K12WB2 is the closest match. This might be slightly longer but should still work. I attached a picture that has all of the dimensions listed. For chrome 60 degree lug nuts you would then want…

view full answer...

Answer 8

Yes, as long as the spare tire is the same size, load range (weight rating) and has the matching wheel bolt pattern you can use a bias ply spare to replace a radial main tire for the short distance you'll travel to get the radial repaired or…

view full answer...

Answer 9

First, the DOT date code on a tire is 4 numbers. The first 2 are the week and the last 2 are the year. So for example if it was 2314 that means that tire was made in the 23rd week of 2014. There isn't a difference between a tire sitting on the…

view full answer...

Answer 10

Hi Lane, The closest option we have to the measurements you provided would be the DeeMaxx Drive-In Wheel Stud - 1/2" Diameter x 2" Long #DE52GR.

view full answer...

Answer 11

There are really two reasons to replace a grease seal, if they are damaged or worn and leaking grease then that is an obvious factor. If you are replacing bearings it is usually best to replace the grease seals as well because although they may still…

view full answer...

Answer 12

The closest option we have and what will work for your application is the Kodiak Wheel Bolt - 1/2" Diameter x 1-11/16" Long #K12WB169. This has a slightly longer knurl, the correct threading and are just slightly shorter at 1.6875 inches.

view full answer...

Will Kodiak Wheel Bolt # K12WB169 Fit if There are Small Differences in Size

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching