Replacement Lug Stud with 0.545 Inch Knurl

Question

Question:

.550 diameter on knurled part. 1/2 20 threads. 1 1/4" or 1 1/2" bolt length

asked by: Dan

0

Expert Reply:

Can you please let me know the what the diameter of the knurled part needs to be? You can do this by measuring the lug studs you current have with a digital caliper to the nearest hundredth of an inch.

expert reply by: Conner L

0

Dan

5/29/2018

.550 diameter on knurled part. 1/2 20 threads. 1 1/4" or 1 1/2" bolt length

Conner L.

5/29/2018

The Kodiak Wheel Bolt part # K12WB169 will be a bit longer at 1.7" long than the studs you have now but should still work for you. It has a 1/2"-20 thread and 0.545" diameter knurl. I have attached a review video on the above stud for you as well.

Answer 1

On Dexter 9/16-inch lug nut #STN569 the thread pitch is 18-TPI. I went to our warehouse and did a test fit of this lug nut on Dexter hub/drum #8-219-13UC3, which meets your description of an 8-on-6-1/2 Dexter hub with 9/16-inch studs for 7K axles.

view full answer...

Answer 2

We don't have exact specs on the part that you're referring to, but I do know that's a stamp on a UFP hub, so I was able to reach out to my tech contact at Dexter UFP and he said that most of the hubs that number would be stamped on use a…

view full answer...

Answer 3

We do have a 1/2" diameter wheel bolt that is close to 1-3/4" long which may work for you. The Kodiak Wheel Bolt #K12WB169 is 1-11/16" long, but that does not take into account the lip of the bolt, as you can see by the accompanying…

view full answer...

Answer 4

We have the part #DX98FR which is 1/2 inch longer than the #K12WB2 that you referenced and is same 1/2 inch diameter.

view full answer...

Answer 5

I took a look at the wheel lug stud LCI SKU 121803 you mentioned, and I was able to find the Kodiak Wheel Bolt #K12WB2. This bolt is 2" long, and has a thread size of 1/2"-20 UNF-2A.

view full answer...

Answer 6

The Kodiak Wheel Bolt #K12WB169 that you referenced should fit just fine. Since all of the differences are small fractions of an inch you are good to go!

view full answer...

Answer 7

First, the DOT date code on a tire is 4 numbers. The first 2 are the week and the last 2 are the year. So for example if it was 2314 that means that tire was made in the 23rd week of 2014. There isn't a difference between a tire sitting on the…

view full answer...

Answer 8

Based on the dimensions you listed it looks like the part #K12WB2 is the closest match. This might be slightly longer but should still work. I attached a picture that has all of the dimensions listed. For chrome 60 degree lug nuts you would then want…

view full answer...

Answer 9

There are really two reasons to replace a grease seal, if they are damaged or worn and leaking grease then that is an obvious factor. If you are replacing bearings it is usually best to replace the grease seals as well because although they may still…

view full answer...

Answer 10

The closest option we have and what will work for your application is the Kodiak Wheel Bolt - 1/2" Diameter x 1-11/16" Long #K12WB169. This has a slightly longer knurl, the correct threading and are just slightly shorter at 1.6875 inches.

view full answer...

Answer 11

Hey Larry, I would recommend going with a stainless steel lug nut like the part #LHLR103 that matches the specs you need. Stainless steel won't rust or corrode. This means they won't swell up either making it hard to fit a socket on.

view full answer...

Answer 12

Yes, as long as the spare tire is the same size, load range (weight rating) and has the matching wheel bolt pattern you can use a bias ply spare to replace a radial main tire for the short distance you'll travel to get the radial repaired or…

view full answer...

Replacement Lug Stud with 0.545 Inch Knurl

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching