Recommended Trailer Wiring Harness for 2014 Subaru Outback Wagon

Question

Question:

Hi, I have a 2014 Subaru Outback 2.5i Limited. I dont know whether to buy the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector-Item # 118467, or the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector Item # C56040. I have read the specs on both items, and have watched the installation videos for both items. It appears they are both compatible with my vehicle, require the same installation process, and do the same exact thing. If you could tell me what the exact differences are, and which one I should buy, that would be very helpful. I am primary going to be towing a 14foot boat trailer. Thank you very much.

asked by: Brian M

1

Helpful Expert Reply:

Both the Tekonsha T-One Vehicle Wiring Harness # 118467 and the Curt T-Connector # C56040 referenced in your question are confirmed to fit your 2014 Subaru Outback 2.5i Limited. As you mentioned, both harnesses will install the same exact way, by connecting to factory ports located in the rear cargo area behind the driver's side trim panel or in the spare tire compartment. The only real difference between the two, other than the manufacturer, is that the Curt harness features a slightly higher maximum amperage of 3 amps per circuit for the stop/turn lights and 6 amps for the tail lights (2.1 amps for stop/turn and 5.6 amps for tail lights on the Tekonsha), however both still offer plenty for just about any trailer light setup.

Even though the Curt harness is a bit stronger in terms of amperage, I actually recommend going with the Tekonsha # 118467. This is simply because Tekonsha specializes in trailer electrical products and they are well known for producing reliable, long-lasting harnesses. We hear far fewer issues with Tekonsha harnesses than we do with those from any other manufacturer.

I have attached an installation video that you can use for reference.

expert reply by: Chris R

1

Answer 1

For your 2017 Chevrolet Express Van we do have brake controller solutions but the vehicle does not have a port under the dash for installing a brake controller. Instead it has wiring available under the dash or sometimes the driver side floor mat up…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 7

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 10

Hey Scott! Your 2026 Ford Ranger may or may not have a brake controller port/plug, even with the tow package. There will be four wires coming out of a large wire harness by the driver side firewall, left of the brake pedal, which can be wired to the…

view full answer...

Answer 11

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Recommended Trailer Wiring Harness for 2014 Subaru Outback Wagon

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching