Running Light Fuse Location 2018 Chevrolet Silverado 2500

Question

Question:

What fuse in truck will it be if there is no power to trailer running lights

asked by: Gary

1

Helpful Expert Reply:

The number 15 fuse in the engine bay fuse box is responsible for the trailer parking lamps. For future reference, the owner's manual will tell you where all the fuses are located and what they do.

expert reply by: Conner L

1

Wayne

10/21/2025

Is there another circuit feeding the trailer lites no pwer to any fuses going to trailer

Jerred H.

10/21/2025

@Wayne You would need to check the fuse diagram on your vehicle.

Answer 1

The trailer running light fuse of your 2018 Chevy Silverado is in the number 15 slot of the fuse box under the hood of your truck. I attached a picture with the location pointed out.

view full answer...

Answer 2

According to my research the following wires for the 7-Way on your 2019 Chevy Silverado 2500 should carry the following functions: Green OR White/Green - Reverse White - Ground Blue - Brake Controller Green OR Green/Purple - Right Turn/Stop Red/Black…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 10

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Running Light Fuse Location 2018 Chevrolet Silverado 2500

Product Page this Question was Asked From

Continue Researching